CDE4205AZW Crosley Dryer - Instructions

The repair was easy, based on the comments from this website. I used a 6-in-1 screwdriver, and that was the only tool. I removed the two screws holding the hinges, removed the door, then the two screws on the opposite side of the opening. This allowed the front panel to come off. I spun the dryer tumbler until the baffle that was loose was at approximately 5 o'clock. I unscrewed the remaining screw and found the missing screw in the bottom of the dryer. I put those two screws into the new baffle, and popped the front back in place. I reinstalled the four screws (two opposite the hinge, then the two that hold the hinges)...all done in about 20 minutes (including vacuuming the lint out from that lower area).

replaced high limit thermostat-303396 and cycling thermostat-306056 approx $48.00. Remove dryer door with 2 screws in hinges and 2 screws on other side.Remove front panel-pull out from top-swing down to unhinge from bottom hooks to expose parts lower front. Small socket for high limit thermostat bolts@heating element housing and same socket for cycling thermostat@blower
exhaust air housing-both easily accessible in front lower area.Unplug power before working inside.

we replaced the baffle by removing the broken baffle. There were two screws holding it in place. Door and front panel of dryer had to be removed to accomplish this task. Quite an easy repair/replacement. Thank you for all your help PartSelect.com.

I followed the directions that came with the conversion kit; which I ordered from PartSelect. Your website was the only place that could help me. Our new dryer is actually a Samsung. The people at Best Buy were no help. I called the Samsung headquarters and a "real" person there told me I could order from them or use a Whirlpool kit because they are the same. You guys were faster in getting me one, so I went with you. My wife was happy. I would recommend you to others.

Turned off circuit breaker. Removed two screws at base of front panel with stubby Phillips-head screwdriver. Swung panel up about 30-degrees, and removed panel, disconnecting red and yellow wire to door switch. Removed four sheet metal screws and took off large drum support bracket. Checked drum support rollers and shafts. They were fine. Reset circuit breaker and turned on dryer. Rattling noise still present.
Removed six small screws holding blower fan assembly. Shaft receiver on squirrel cage fan was worn completely round (it should fit onto a half-round shaft). Ordered new blower fan from PartSelect.com. Replaced tonight, and it works beautifully. This dryer is 29-years old. All it's ever needed in the 10-years I've owned it is a belt replacement and this repair. Long live the 1970s Maytags, and good parts suppliers like this one.

Removed the screws and took the door off then took the front panel off and popped up the top. Then pulled the drum out. Took snap ring pliers and removed rollers and replaced with new rollers then vacuumed all lint from machine and reversed operation to put everything back together. Operation was a total success!

remove 4 screws allow removal of back metal cover
slide control panel toward rear to disengage plastic line up tabs
lay panel face down on soft cloth
remove 4 screws to allow removal of control board from panel
swap electrical connections from old to new unit
reassemble

Note: You may want to consider replacing the 2 Drum Support rollers at this time (while your in there)

1. UNPLUG YOUR DRYER FIRST.

2. Using a phillips head screw driver - Remove 2 screws that secure the dryer door hinges to the frame, Lift door very slightly to unhook hinges and pull out door with hinges attached as straight as possible, set aside. Remove the 2 plastic tabs from the opposing side of the door hinge also secured by screws.

3. Remove the front panel (panel is shaped like a football goal post) by tilting out the top ends of the front panel toward you, then lift up to remove panel from the bottom metal retaining tabs.

4. Remove the 2 hexhead screws from the 2 retaining clips (security hooks) that secure the top
of the dryer closed.

5. Systematically remove the hexhead screws from the rest of the front of "shroud" (it holds (suspends) the drum in place between the front and back of the dryer).

*** I didn't disconnect any wires, I carefully swung out each piece that had wires attached, propped up those parts vertically ensuring no strain on the attached wires. Others may want to disconnect wires to avoid breaking or damaging them.

6. Vacuum out any dust/lint that may be present.

7. Draw a quick diagram of how the underside of the belt is threaded on the idler pulley and motor pully first. Release the tension of the belt from the underside of the drum. The easiest way is to push the idler pulley arm away from the belt and slide off the belt from the idler pulley and motor pulley. Slide the drum out.

8. Remove the hexhead screw from the bottom of the idler arm. Disconnect from retaining spring.

9. You may only need to replace just the Idler Pulley Wheel. I recommend replacing as a "unit" the Idler Pulley Wheel, Idler Arm, Ring-E and Idler Shaft Washer(s) - then you can just swap out the old one for the new one.

10. Reassemble

(When reassembling the belt - place around drum first and slide drum in place. Now from the underside-place (drape) belt around the motor pulley (it will be very loose) Now push the idler pulley arm toward the motor pulley, engage the left side of the belt around the idler pulley and slowly allow idler pulley to increase its tension on the belt) You can test manually by rotating the drum by hand to ensure proper movement.)

Turned off gas and unplugged dryer
1) Removed bottom front panel
2) lifted top panel up like a car hood
3) Removed door springs
4) disconnected electrial connections to door unit, removed door unit
5) removed drum, scraped old felt from drum
6) glued new felt with a very strong glue (nanoglue or gorilla glue, same thing), let it dry overnight
7) secured back inside panel, replaced drum and put dryer back together.

First I performed a keypad check by measuring the contacts on the keypad connector per the service manual I found online. All buttons appeared to be functional. I purchased both the LED Electronic Board and the KeyPad. Turns out the problem was with the KeyPad (stuck key) even though all key seemed to have checked out. So now the dryer is functioning with just the replaced Keypad and I have an extra LED Electronic Control Board.

Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.

We tried replacing the door switch first, still didn't start. Next we tried the thermal fuse and it turned on and has worked ever since.

Instructions were great. Very step by step. It could not have been easier. Repair saved me a $100 service call.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

Removed back cover from control panel, unscrewed screws securing panel and unplugged wire leads, then removed. Replaced with new panel by plugging back in wire leades(color coded,very easy) resecured board and cover. Done