CDE4205AZJ Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from OAKWOOD, OH
- Parts Used:
- WP33001762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer would not run; blown thermal fuse
unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from REVERE, MA
- Parts Used:
- WP33002032
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Long baffle had broken off inside the dryer drum.
Removed four screws from the door hinges and front panel. Removed the front panel by pulling forward from the top and found two screws. The part does not come with screws which are #10 x 1 and 1/4" long hex head sheet metal screws. I believe that the screw size is critical as the part may break loose again if the screws width is too large or small for the predrilled holes in the baffle. One set of holes in the drum had slotted screw holes which would allow for installing the baffle with the screws partially installed in the baffle. I would recommend washers for that installation. Check all three baffles to ensure that all screws are tight.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Brookfield, WI
- Parts Used:
- WP33002032, WP33001808, WP33001755
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
baffles broke off
Unplugged dryer. Removed dryer door with philips screwdriver. Removed front dryer panel aftr loosening philips screws on each side of door. Then at top right corners I used a nutdriver to remove clips/hooks that hold down top of dryer. I then lifted top of dryer up- it is hinged at back. I could then manually turn drum to access screws that hold baffles. I held each baffle in place with left hand and turned in screws with right hand until tight, using nut driver. I vacuumed out inside of dryer. Reassembled top, front panels and door. plugged in and tested. All good.
Was this instruction helpful to you?
Thank you for voting!
dryer not getting hot enough
my son did the installation according to your excellent video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Marion, IN
- Parts Used:
- WP33001808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken lint filter.
Take old out, slide new one in. Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Warsaw, IN
- Parts Used:
- WP33002032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken Baffle in Dryer
Removed Dryer Door and front face of dryer, total of 4 screws, turn dryer drum to position broken baffle screws, remove screws, install new baffle, attach front face of dryer and reattach dryer door. Time 15-30 min. total. Real easy. Thank You PartSelect. Maytag told me my part was no longer available, but I fold it at PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from WOODBURN, IN
- Parts Used:
- 306508
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
front glides wore out
Followed instruction video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from CLAY, KY
- Parts Used:
- WP33002032
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
baffles broke
take screws out of front of dryer, pull front off to expose drum and replace baffle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ignas from Midpines, CA
- Parts Used:
- WP694674
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
electric dryer stopped heating - the thermostat got very hot
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from ANSONIA, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The female catch in door was bro9ken
I took out the old worn out part and replaced with the one I order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Powell, OH
- Parts Used:
- WP33001808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken lint screen in dryer
I had to call and reorder because I ordered the wrong part and the gal on the phone cancelled the first order and the right part came the next day!Amazing service!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Portland, ME
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not close
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sandra from prairie vilage, KS
- Parts Used:
- WP33001808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the screen on the lint filter had ripped
took out the old lint filter and put in the new one.
It fit perfectly! the part arrived quickly.
I was very satified with my experience!
It fit perfectly! the part arrived quickly.
I was very satified with my experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Somersworth, NH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench set
replace door closer
Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martina from Annapolis, MD
- Parts Used:
- WP33002032
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replaced tall baffle
Unscrewed door and front panel. Pulled and took the, off. Used standing flashlight to illuminate the area underneath the dryer barrel. Tried various tools to take out broken plastic remnants. Then, used small electric nutdriver to screw the tall baffle into place with newly purchased metal screws. Was a bit hard to reach and tight but finally worked once I found an appropriate tool and top.
Was this instruction helpful to you?
Thank you for voting!