TEA800 (P75752-5W) Amana Dryer - Instructions

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

Removed the 2 screws from the bottom of the front panel and pulled the cover up and out. Labeled the wires to the light and door switch and disconnected. Lifted the belt tensioner arm and unlooped the belt from it and the motor. Removed the 4 bolts that hold the front drum support on then held the drum up and removed the support. Pulled the drum out slightly and allowed the rear to drop, at this point you can get to the rear rollers without pulling the drum out of the machine. The roller shaft was so tight I had to put a straight-blade bit in a 1/4" socket to get enough torque to break it loose. Make sure to use a large enough driver or you will strip the slot out of the screw. This model had a nut on the back but I was able to just drag my finger against it to get it apart. Removed the washer and roller from the shaft and cleaned the shaft and washer with WD40 before reinstalling with the new roller. Vacuumed all the lint I could get to and reassembled, lift drum, push back, front support, 4 bolts, belt, wires, front panel, 2 screws.

Followed video on PartsSelect website, they made it real easy.

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

one screwdriver, one new door latch, five minutes! Pried out the female part of the door latch, tapped in the new one and started the dryer. Never had an easier repair. Usually there is some hitch along the way you learn about the hard way, but not this time. TOO EASY!!

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

I thought it had to be the igniter so I replaced that part. The dryer still did not start. I replaced the high limit and hoorah dryer works. Two weeks go by, the dryer is drying the clothes but my wife smells gas in the laundry room. I replaced the coil pak on the gas valve. My wife says she still smells gas. I replaced the radiant flame sensor and no gas smell for 2 weeks now.

popped out the old, broken female latch, popped in the new one in less than 30 seconds. We had been leaning stool against the dryer door for 5 years. Now it works exactly like it is supposed to.

After the Radiant Flame Sensor was installed, the problem remained. An appliance repair person then replaced both coils, and that fixed the problem.

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

I followed the video on the site which was really helpful.I took the door off without problem. I had to take the bottom panel off the front and unscrew screws on large front panel.Replacing the latch was a breeze. Just as shown on video. Be careful that dryer drum doesn't fall down off wheels. My did and had to push it back up.Replaced all panels and screws and it works great.

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

Replaced the Latch

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.