DLE330RC-PDLE330RC Amana Dryer - Instructions

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

very well had to take blower assy apart with no problem ownly problem I had was getting the belt lined back up but got it and it works great

The Dryer is about 25-30 years old. I replaced the motor due to overheating, while I had the dryer disassembled I decided to change out the idler pully wheel and the drum support rollers. This was my first time changing out the motor. Surprisingly, the blowerfan blade came off the shaft of the motor very easy. I was concerned about the age of the dryer and was anticiapating this could be a problem fortunately, it came off very easy. Removing the old motor was easy. The only issue I had was seating the new motor in the correct position. I felt that the motor was not in the correct posiotion however, I was not sure being that this was my first install.
After trying several times, rotaing the motor back and forth (side to side) within the motor holding end brackets the motor fell into place and I was able to put on the end motor clamps on correctly. The drying is now working.

I followed the online video on PartSelect website. No other instruction necessary.

We received the parts in two days. We installed the new lint duct assembly in about 30 minutes. We unplugged the dryer and lift ed the top of the dryer removed the front of dry we disconnected the wiring and then removed the damaged lint duct . Cleaned the lint off the dryer and replaced the new lint duct. screwed the front back on . Reconnected the wiring clips and put the top back on the dryer. The top of dryer had clips that slid the top back on. Plugged dryer in and it works great.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

Step by step, I removed the bottom front panel with a putty knife to compress the spring clamps, removed the inner lint trap, disconnected the door switch and springs and blower connection under the drum, removed the lint trap/ blower housing, remove nuts at bottom sides of door panel, lift top front of dryer (putty knife, spring clamps) to remove nuts at the top then removed the door panel. I then released the belt from the (spring) pulley and pulled the drum out. Pay attention to how the seals were put on! I removed the old seals and cleaned off the old adhesive with acetone and a steel scrubby( wear gloves when using acetone and when applying new adhesive, and work in a ventilated area!) Follow instructions for applying the adhesive for the seals. Put back together in reverse order. Repair successful!

This amana dryer didn't have the lower panel with screws. Instead, I removed the brackets in the back and found that the whole top would separate from the rest of the body (except for wiring, of course.) There seemed to be screws holding the top to the base in the front, but these are just guide posts. There are two spring clips in the front that you can pop loose with a putty knife.

Then there are two screws inside that fasten the front to the rest of the frame. Once I removed these, and the electrical connections to the door switch and the light bulb, the whole front came of just by tilting it forward and pulling the front panel up off of metal tabs on the base.

The rest of the repair went smoothly per other descriptions.