Models > LE8517W2B-PLE8517W2B > Instructions

LE8517W2B-PLE8517W2B Amana Dryer - Instructions

Jump to:

All Instructions for the LE8517W2B-PLE8517W2B
121 - 135 of 479
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Keith from CARLISLE, IA
Parts Used:
WPY54414, WP40111201, WP37001298, WP37001042
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
All the videos and directions
showed starting withe removal of the dryer top. With my dryer, I needed to start by removing the bottom front panel (2 screws). Next the door panel (2 screws). Now I could remove the top panel (2 screws). From here, the tear down went like the directions th My biggest problems were, figuring out I didn't start with the dryer top. Then getting a proper sized snap ring pliers to remove the drum rollers and and the idler pulley.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from OCEANSIDE, NY
Parts Used:
WP40111201
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
trouble with lining the drum on the rollers after belt installation
disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ted from Lakeland, FL
Parts Used:
WPY54414, WP37001144
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench set
Dryer was making squealing noises
It was pretty simple, really. Quite honestly, Parts Select was the first website that had my model number listed, and even had a diagram of the dryer. Once I removed the covers, it was very obvious that the belt tension pulley was bad, One side was worn away. I ordered both parts, the new pully, and the tension arm with the bearing, since I had no way to tell which was damaged, causing them to bind. They simply bolted to the motor assembly. The hardest part was reassembly. Getting the front panel on and being sure that the tabs holding it in allignment, and that the drum spun freely was really the only concern. The repair took less than 1 hour, and after seeing the inside of my dryer, I am convinced I can easily replace ANY part of this appliance and keep it running as long as I can find parts.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Troy from Huffman, TX
Parts Used:
WP37001042
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
loud squeak/grinding noise
Used a dolly to move the drier out in the garage to give myself some room to work...remove the bottom panel--2 screws at the bottom...remove the door--2 screws at the bottom of the door, disconnect the 2 switch wires and then it slips out of the top....remove 2 screws from the top and swing the top all the way back out of the way---it'll just hang there.....remove the front drum support--4 screws.....slide the drum forward while working the drive belt off of the drum.....you can now see the 2 drum support wheels.....at that time I got my shop vac and got all the lint and crud outa there......remove the snap ring on each wheel, slide off the washer and wheel, pay attention--the wheel has a front and back.....reinstall the new wheel with washer and snap ring (i put a small dab of grease on the wheel support)....I also put a dab of grease on the belt tensioner wheel support--same little snap ring retainer.....reinstall the drum by sliding it in slowly as you work the belt back into place....install the front drum support--roll the drum by hand to make sure your belt is on properly.... resecure the top, then the door, and finally the bottom....when facing the drier my left wheel was in way worse condition----this is obviously because it is located right in front of the heating element....thanx and good luck....
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pamela from Sanbornton, NH
Parts Used:
WP40111201
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
The belt that turns the dryer broke
The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Theodore from Madison, CT
Parts Used:
WPY54414, WP23748, WPW10121334
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dryer squealed when first starting for about 3 minutes
Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Juneau, AK
Parts Used:
61927
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dryer had no heat
Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Lincoln, NH
Parts Used:
61927, WP40111201
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
no heat and worn out belt
The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arlene from Gig Harbor, WA
Parts Used:
502140P
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
on old lint trap was coming apart at the seams
Initially I was concerned the trap was too long but it worked perfectly and I was thrilled. Thank you for your good service. It was easy in that the model # confirmed the part. Many thanks
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Todd from Red Lake, MN
Parts Used:
WP37001298, 12002090, WP500121
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Dryer was making a grinding sound
I opened new parts and stcuk a felt pad on each glider and put one of my 10 lb. weights on it for about 1/2 hour to help it stay in place.

Then removed top panel and then the front..There are three phillips screws that hold the lint catcher in place inside the barrell. Then remove the 4 total bolts to remove Glide Brackets.

Mine was so worn down that the barrel had rubbed alomost all the way through a bracket.
Once felt pad was firmly set, i attached glider into bracket and installed them.

Put everything back in place and started up..and it was running and sounding like new...i paid 27.00 for parts and saved big time compared to what a service shop would have charged me.

The shipping was super fast and with my wife and i having 9 children in the house it was a life saver for us.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathy from Anderson, IN
Parts Used:
WP40111201, WP37001287
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Noisy
Removed front cabinet panel, removed lint/front drum panel, removed drum and belt. Removed spring from idler lever, replaced idler lever. Installed drum with drive belt, reinstalled front lint/drum cover, reinstalled front panel.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JEROME from NILES, IL
Parts Used:
W10169313
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
switch clip broke
Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from POMPTON LAKES, NJ
Parts Used:
WPY54414
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Loud screeching from idler pulley
The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pete from ANAHEIM, CA
Parts Used:
W10169313
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The door switch was defected
The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from SAGLE, ID
Parts Used:
WP40113801
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
No Heat
very easy after the learning curve. I ordered this thermal fuse on Friday morning and got it Monday by 11:00 am. I love this kind of service. I will use this company again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LE8517W2B-PLE8517W2B
121 - 135 of 479