Models > LE8517W2B-PLE8517W2B > Instructions

LE8517W2B-PLE8517W2B Amana Dryer - Instructions

Jump to:

All Instructions for the LE8517W2B-PLE8517W2B
106 - 120 of 479
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ron from Portage, MI
Parts Used:
56000
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
Loud Grinding type noise - Broken Blower Wheel
Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Priscilla from Portland, ME
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dryer door would not close
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Erwin from Somersworth, NH
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set, Wrench set
replace door closer
Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSEPH from ANSONIA, CT
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The female catch in door was bro9ken
I took out the old worn out part and replaced with the one I order.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Milton, FL
Parts Used:
WPY54414
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Loud Squealing Sound When Dryer Is Running>
First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ron from Mellen, WI
Parts Used:
61927
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
dryer not heating
Well first of all you get to the back of the dryer from the FRONT.. after lower panel was removed location of the heating element was right in front of you. Two 7/16 sheet metal screws hold the heating element in place very easy to remove.. upon removal you will have plenty of room to pull element out and switch out the wires you need to do.. Upon examination I think my trouble was a high limit fuse that burned out, so I propably did'nt need to buy the whole element ( you might want to check that first it is the ceramic one ) cleaned everything out and dryer is as good as new Good luck
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PAUL from GRESHAM, OR
Parts Used:
WP40111201, WP37001287, WP37001042, WP500121
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set, Wrench set
Screaching on start-up, then continuous after time
Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Prudenville, MI
Parts Used:
WP37001287
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Idler lever needed replaced
Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rick from Marlborough, MA
Parts Used:
WPY54414, WP40111201, WP37001298, WP37001042, WP500121, WPW10121334
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Noise and Heat will not stay on (Gas Dryer)
Parts that were recommended for the noise issue were spot on. Instructions were very helpful and made the job go very smooth. Replaced the belt, rollers don't forget to order (2) felt pad and idler pulley replaced.
The part suggestions for the heat problem did not fix the problem. The burner flame would come on for 2-5 min. then go off. A few min. later the burner would try to ignite but would not start. The igniter would get cherry red but no activation. I end up replacing the coil kit. Turned off the gas removed (2) screws and wala done 5 min. and it fixed the problem.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nick from Mesa, AZ
Parts Used:
WPY54414
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
The belt wore a groove in the belt tention roller and started sliping.
I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wilford from Long Grove, IA
Parts Used:
WP37001042, WP40111201
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Dryer was making an awful noise.
I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Mendota, IL
Parts Used:
WP40111201
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
Belt on drum was sqeuling on start up
Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROBERT from RICHMOND, TX
Parts Used:
WPY54414, WP37001042, WP40111201
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers
very bad screaching noise when drum was inmotion
First we had to virtually take the entire dryer housing apart - not very user friendly. We found that one of the two mounting screws on on of the rollers was gone. The mount was just wobbling around which caused the roller to fail and all of the noise. The wheel removal was a bit tough since there is very little room to pull it up and off of the center post. Definately need at least one helper to pull up on the drum while the wheels are removed and installed. Once the two new rollers were in place, the dryer worked like it was new. Not an easy job, but very do-albe - saved a ton of money doing it myself. Two must - haves: good set of snap ring plyers and one patient helper.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from ridgecrest, CA
Parts Used:
WP37001132, WP37001042, WPW10121334
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
the drum was clunking and scraping,also it had begun to eat clothing
I disconnected power and vent hose then tipped dryer on its back. I took off lower panel and door ,disconnecting wires to door and light and hanging them over the side,i then removed the front plate and felt seal the plastic fan shroud and lint trap come out as one piece along with the front plate.when i could look down on the drum,standing on the left side ,i disconnected the screw connecting the top plate to the left side plate allowing the top to gain a little play,this is the amount needed for the drum to be removed,pull belt tensioner slightly as to release tension remove the belt from motor shaft.At this point remove drum and set aside,the lower felt ring and support rollers will be exposed as well as tension spring and tension roller,i used a mirror and guided the snap ring pliers into place on the tension roller,At this point pull on rear felt ring it may come loose easy ,if not work some adhesive remover into the cracks where the glue is and keep agitating it ,eventually the glue will begin to release and more and more of the remover can get in washing the felt ring off,clean real good after using remover soap and water and allow to dry ,apply a thin ring of high heat adhesive smooth out to spread even all around when it becomes tacky begin applying new felt ring,while this adhesive cures perform the same procedure on the front panel and its felt ring while these rings are drying into place undo snap rings and pull support rollers out and replace in like order replacing thrust washers and snap rings if you damage them ,the roller on the tensioner is more tricky but if you use a mirror and a light it is easy to sneak in there lastly when preparing to reassemble and drum and belt are in place just before you replace the front panel it is prudent to replace the neoprene slides,reassemble front plate and ensure that the felt ring lines up and goes in evenly all the way around re-attach top left corner ,reinstall door and wires as well as bottom plate this will conclude the procedure i learned all of this the hard way i should have just replaced all the parts at once i was in that machine 6 different times Daniel 2017
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward D from GRAND BLANC, MI
Parts Used:
WP40111201
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set
Belt deteriorated, cracked, slipping
I just followed the video instructions and really they were not as good as some of the customer descriptions which were far more detailed. It was like an experienced repairman telling another experienced repairman how he has been doing this repair for 20 years. The customers get into the kind of detail that is very helpful. More important parts select never tells you to read the blogs first before ordering your parts. $100 later I bought a new GE dryer which I would have done 10 days ago had I known Maytag has a repetitive problem with the high limit thermal fuse which no one has a cure for. So I did a whole bunch of repairs replacing parts on a dryer which needed to be replaced.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LE8517W2B-PLE8517W2B
106 - 120 of 479