P1118309WL Amana Dryer - Instructions

remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.

removed drum and motor and installed new parts. Very fast service on parts. Well be back if needed.

Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

Popped in the new part. Really! That easy!

as described in video. Very well done. Thank you

My problem was that my AMANA dryer would not heat. The site suggested testing the two thermostats so I opened the dryer but didn’t follow the instructions in the video tutorial on the site since my AMANA is different. I used a nut driver and needle-nosed pliers for the whole job. Here’s what I did:

1. Unplugged the dryer.

2. Disconnected the exhaust pipe at the dryer.

3. Pulled dryer away from back wall about two feet.

4. Removed the two bottom panel screws (floor level) and removed panel.

5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.

6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).

7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)

8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.

9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.

10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.

11. Used the belt to lift and remove the drum through the front opening.

I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.

I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.

Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)

I closed up the dryer by reversing the opening steps.

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.