P1118309WL Amana Dryer - Instructions

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Just follow the video. The hardest part is getting the top to disengage from the clips.

Followed video on PartsSelect website, they made it real easy.

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

First I removed the two screws that held the timer in place. then screwed the new one in place. I then held it to one side and swaped the wires one at a time [8wires] so as to insure the wires were in the correct location. Replaced the cover and dials and it works good as new. My wife thinks i'm the greatest. Thanks,Tommy

removed a couple of screws and replaced the new fuse . the dryer is heating up ok now.

p.s thank you for the quick deliever on the part, . as i was only with out the dryer for two days

Thanks
JoAnn

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

I dismantled the dryer and replaced the thermostat and the heating element. The online videos are excellent. Thanks

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.

Took off the two lower front screws, Then the screws to take off the door and frame. Then the lint trap. Finally took out the drum. BOY WAS MY DRYER DIRTY WITH LINT! Vacumned it all out and washed the filter and filter housing with soap. Found out that I needed tension wheel also. Ordered that. Replaced the wheel, that was the hardest part. Need to take off this part like a "spring washer" and put it back on with the new wheel in place. Then placed the belt on the drum, belt on the tension, screwed the drum holder frame on, screwed the door frame on, screwed the lower panel on and it works great. By the way I am a female and if I can do it anyone can.

Removed the front dryer panels (lower & upper), front drum support and drum. This gave me easy access to the idler pulley and tension spring. I also took the opportunity to vacuum all of the lent that had collected over the years. After installing the new parts and aligning the belt, I reassembled the panels, plug it in and it worked like a champ! Locating the parts on your website was fast and easy. I appreciate it and thank you.