DV3C6BEW Amana Dryer - Instructions

I originally called a repair person to come out but that was a total waste of time and money. He removed the front of the dryer claimed there was a dryer sheet causing the problem and put it back together.
Never again!
I watched a youtube video for step by step instructions on how to take the dryer apart.
I took the front door of the dryer off, removed the filter cover and the dryer drum & belt. Removing this was simple and allowed me to see everything I was working on. With the new part in hand, I removed one wire at a time from the non working heat sensor and connected it to the new part. That way I was sure I had the right connections.
I then removed the thermostat making sure to put the new one back in place exactly as the old one.
I then put the drum back in place with the belt securely fastened. I put the cover back on the lint filter and placed the dryer door back on securing it in place. The dryer is now working perfectly. It takes longer to take the dryer apart than to replace the old parts.

This repair is easy. The only drag to this repair is you need to almost completely dismantle the dryer just to get to it. So keep track of your screws.........Look on you tube for videos to dismantle the dryer, you will need to take this down to the drum to change....Once I replaced the pulley, it was about 30 minutes later the dryer was operational again.

I removed the dryer vent and cover to take a look at the inside of unit. Then I saw that wheel on the pulley was damaged and belt was tangled up. I simply replaced the pulley and placed the belt back. Samsung advised that I replace the unit, but myself $800+ on a new unit.

Followed the video on the website and finished it in a short time. Now it works like a new dryer.

Follow the video instructions.

Disassembled and tested each part with a multi-meter. Found that the thermostat and fuse were bad. Replaced parts and it is working again.

Thank you
partselect.com for a much better heavy duty belt than the original. Way over priced, but well worth it. After watching the video & following it step-by-step, I now have a perfectly running dryer. P.S. don't forget to plug back in the (3) wire harnesses. The entire experience was a great feeling of accomplishment. Thanks again partselect.com

I'll make this quick. To access the motor you need to take half of the drier apart. I cut a access door on the side where the motor is with a small electric saw. It gave me clear access to the motor. You still need to take the front cover off to remove the blower wheel . One more thing, make sure to have the belt back on when testing, otherwise the motor wont start. It took me about an hour and 15 minutes

The design of my dryer is a bit different from the video on PartSelect - but it is very close. And if you watch the really good video on PartSelect plus a few others on Youtube you can figure out how Samsung in general designs the different components. You can fix this yourself definitely.

Cost of part to fix - about $50.
Repairman - didn't even ask. Would probably be $300-400.
Cost of replacement $1,000.

I rated the repair "A bit difficult" only because this is the first time I have ever repaired an appliance. If I were to repair this one again, I'd rate it as Easy.

I'm really thankful for the PartSelect video. This makes DIY repairs possible.

Thanks.

Removed top of dryer, control panel, front (door) panel. Removed screw holding heating element and housing assembly in place, and removed wiring connections. Attached wiring to new heating element and housing assembly, installed screw to hold in place, replaced front (door) panel, control panel, and top of dryer.

Ordered part on 8/24/22. Received wrong part twice now. It is 9/10/22 and I am waiting for the third. Right part number on package but it contains the wrong part. Beyond mad!

I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto [email protected]

Followed video and YouTube most was easy.... put the hooking up the belt took time

Took off the back of the dryer and replaced the thermistor. A $7 part that would have been a couple hundred dollars if we had to call a repairman.

I was working on my daughter’s Maytag dryer model MDE 9700 AYW. The dryer had been making a bumping sound for some time. It had the same symptoms a few years back, but it was still under warranty. The repairman had to replace a drum roller. He told her at the time he should replace all of them but he only had one with him. So when my daughter heard a similar sound she assumed it was a drum roller again so I ordered the roller without taking the dryer part. She has four boys that generate a lot of laundry, so she needs her dryer daily. I wasn’t sure how long it would take to get the part or do the repairs. The roller arrived very quickly, I think in a couple of days. The drum rollers on the dryer did not need to be replaced. What I found was bumping the side to the dryer because the sheet metal had popped inward. The drum has very little clearance on either side. The side probably could’ve used another crease or something to make it more rigid. My time wasn’t, wasted. I think it was will spent. I found that 3+ years of lint at piled up significantly on everything. The lint on the shroud for the heating coil had already turned brown and could have caused a fire. I would suggest to anyone who’s had a dryer for a while should open it up and vacuum out the lint buildup.
It only takes a Phillips screwdriver and very little time. It’s a very little investment for your peace of mind.