4KAED5000FW0 Admiral Dryer - Instructions

OPENED REAR OF DRYER TOP PANEL, TESTED FOR CONTINUITY ON TIMER, ALL TEMP SENSORS AND HEATER COIL WITH MULTI-MEETER AS DESCRIBED IN ONLINE YOUTUBE VIDEO FOR WHIRLPOOL DRYERS. TIMER TESTED BAD AND REPLACED TIMER. EASY TO UNSCREW AND UNPLUG.

I REMOVED THE OLD TIMER AND INSTALLED THE NEW ONE. ALL I NEEDED WAS A 3/8 SOCKET AND IT TOOK LESS THAN 15 MINUTES. I USUALLY CANNOT FIX ANYTHING AND THIS WAS VERY SIMPLE AND THE VIDEO SHOWED ME EXACTLY WHAT TO DO. THE PART IS WORKING OK SO FAR.

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

Replaced 4 wheels and new belt

Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

nobody has said it yet so... to take a dryer apart, take the back off, pull the lint trap, remove two screws on back of the top piece. the whole top shifts forward and disengages two clips on front corners, it then tilts up and back. the front comes off next, this frees up the tub. all parts ordered replaced worn parts, though there was no smoking gun as to the source of the sound. once it was apart, it was a cakewalk. had it up and running in 45 minutes. can't see how it took others two hours.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

Step 1: Unplug the unit, then remove the lint screen and then remove the two screws beneath the lint screen cover. Step 2: At the rear of the dryer there is a small protective metal panel near the upper part of the dryer - remove this first; then at the front of the unit, insert a plastic pry tool between the front edge of the top and the front panel of the dryer and gently pry the top loose. Step 3: Lift the dryer top up and either remove it entirely or let it rest on the back edge and a wall for support. Step 4: On the inside of each side panel near the top front, locate the two screws holding the sides of the dryer to the front panel and remove them. Step 5: Carefully slide the front panel up so that the panel detaches from two metal clips holding the front panel onto the side panels. The drum will likely drop down slightly at this point since it is no longer being supported at the front. Step 6: On the front panel there is a wire that connects the front panel door switch. I left that intact because it was too difficult to remove without risk of breaking it and instead simply set the front panel to the side of the dryer - but if possible remove disconnect the wire and then set the front panel aside. Step 7: Remove the drum by pulling it out, inspect the back felt seal for wear and also the plastic split ring bearings at the front end. When you remove the drum belt the tensioner pulley underneath the drum will likely fall over, but this is to be expected because without the belt and drum providing tension, the piece only fits loosely in a slot at the bottom of the dryer. Step 8: Inspect the drum rollers, motor, and other parts for wear, then vacuum out the inevitable lint and dust inside the unit. Step 9: At this point I also decided to inspect and clean out the lint chute at the back of the unit, so I removed the protective back cover and removed the screws holding the lint chute in place. I then cleaned out the lint that builds up over time inside the chute and checked the two foam lint chute seals at the back of the unit - these needed replacing so I removed the old deteriorated foam and vacuumed off the back of the unit and then adhered the new seals to the back of the dryer. Step 10: Take the new multi-rib belt and drape it around the drum with the ribbed side against the drum - you will likely see a mark around the drum where the old belt was positioned, so use that as a guide. Step 11: Since one of the split ring bearings on my unit was worn, I replaced both at this time by simply pressing the plastic tabs out of the slots at the front of the drum, removed each half of the ring, and reinstalled the new parts - they only correctly fit one way so that the plastic edge lines up cleanly with the front edge of the drum. Step 12: With the felt drum seal toward the back replace the drum - I used a small box to support the drum upon while I reinstalled the drum - this will make it much easier to manipulate the belt around the tensioner and motor. At this point I reached underneath the drum and reinstalled the tensioner. by positioning it in the two small slots near at the bottom panel that are near the front of the dryer motor. Then take the belt and pull it through the tensioner and around the motor pulley at the front of the unit. You will likely have to push up slightly on the drum and tensioner to allow the belt to be pulled through the tensioner and around the motor pulley. Step 13: Rotate the drum slowly by hand at least one full revolution and check to see that the felt seal at the back is not pinched and that the belt does not fall off the pulley. Step 14: I removed the box supporting the bottom of the drum, then took the front panel and fit the front of the drum against it so that the split ring bearing matched up to the front panel. Step 15: The drum will still be somewhat loose and that allowed me to carefully lift the front panel up and then slide it down back onto the two metal clips that hold the front panel to the side panels. Step 16: Reinstall the two screws that also hold the front panel to the side panels. And if you also removed the wire connection to the dryer door, reattach that too. Step 17: If you removed the lint chute, reinstall it from the back while the lid is still off so that it is easier to slide it into position. Step 18: Reattach the top of the unit by seating it against the top of the frame (of course if you disconnected wires, reattach those too) and reinstalling the two screws underneath the lint screen cover. Step 19: Reattach the rear panel cover and small protective metal panel. Step 20: Reattach the flex-hose to the lint exhaust.

When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked up the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.

I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.