4KAED5000FW0 Admiral Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from East Earl, PA
- Parts Used:
- W10861225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle on my Maytag Dryer broke off while opening
When the part arrived I opened it and just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dillard C. from Vina, AL
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Fort Myers BEach, FL
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken drum belt
I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from New Bedford, MA
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken handle
1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Dayton, TX
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter wore out had to be replace
Changed out the lint filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Virginia Beach, VA
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door catch
The original door catch had broken and would no longer stay shut. Ordered the part from this site with ease. Very easy to replace the broken door catch on my Amana dryer. Tool needed was a flat head screwdriver to loosen the cover, remove broken piece and easily replace with new part. Followed the video and it was back to normal operation within minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from JACKSONVILLE, FL
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a new lint filter
Took the old one out, replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from N RIDGEVILLE, OH
- Parts Used:
- W10861521
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace dryer door gasket
Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from appleton, WI
- Parts Used:
- WPW10359270, WPW10359269, 349241T, WP348197, 341241, 279441
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
loud shrieking sound when it ran
nobody has said it yet so... to take a dryer apart, take the back off, pull the lint trap, remove two screws on back of the top piece. the whole top shifts forward and disengages two clips on front corners, it then tilts up and back. the front comes off next, this frees up the tub. all parts ordered replaced worn parts, though there was no smoking gun as to the source of the sound. once it was apart, it was a cakewalk. had it up and running in 45 minutes. can't see how it took others two hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from SUNRISE, FL
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
handle broke off
I easily popped the new handle on in 3 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VENICE, FL
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The dryer door handle broke.
Replaced with new handle in 10 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HUNTINGDON VY, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad screaming noise
Replaced 4 wheels and new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- connie from NEWARK, OH
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
rollers on the tub had worn and the tub was no longer balanced.
sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.
Was this instruction helpful to you?
Thank you for voting!