DE18F2HW Admiral Dryer - Instructions

well, the hardest part is getting this thing apart - you have to take out the lint trap and remove the two screws from the top. Then I was trying to lift the top off - it's held in place by clips so you have to gently but firmly lift it off from the front end and let it open while still semi attached at the back (like a chest). Detach the electrical wires - they are just clipped in place. Then remove the screws (one on each side) that attach the front panel, and (and this is the hardest part if you don't know how it's attached). You have to SLIGHTLY LIFT the front straight up and then pull it away towards you. I just pulled it off, breaking the little attachers, which I subsequently had to weld back on with a welding compound and leave it overnight to set. the next day was pretty easy though...

The spinning drum is pretty easy to get out and you set it aside. Then I saw the belt pulley sitting there on the bottom of the dryer out of place -- fortunately with the belt there came instructions on how to instal it - READ THOSE INSTRUCTIONS - after that it's cake - put the belt around the center of the drum and feed it through the other parts underneath (this is easier if you tilt the dryer back a bit to get at it better. And you must pull back on that pulley after you have put it in place again - clips into the bottom of the dryer - it's supposed to have a lot of tension on it. Put it all back together and voila!

good luck!

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!

Opening the dryer to discover the problem was easy. We put the belt up on a workmate bench - I think this made access better at the bottom. Getting the new belt on past the rear drum seal was ok, the instructions could benefit by including wording describing how to roll the belt flat under the 2 rear drum support pulleys to bring it to the drive motor shaft pulley. The instructions included with the belt had a diagram showing the position of the belt take up idler (the idler was found loose inside the bottom of the dryer), our dryer had a hole in the metal spring clip of the idler arm, so we thought at first that a screw to the chassis had broken - this is not the case the idler pulley is held in place by belt tension, so pulling the spring clip open while feeding the belt would have been useful in the instructions too. Other than those 2 head scratchers the repair was easy and saved us the cost of calling a repairman. Thanks PartSelect.

My 12 year old son and I took off the front of the dryer to see if we could see what was wrong. The belt was snapped and on the floor of the dryer. I ordered the belt from you--it came three days later. That evening, my son held the drum while I laced the belt through the pulley. We cleaned everything up--lots of lint! Put everything back together, plugged it in, turned it on--SUCCESS! We were wildly excited. I am a stay-at-home mom determined to save money any way I can.

I followed the posted directions from others, and it was a breeze. They were really helpful. I would just add the step of keeping the drum in place with a block of wood underneath before removing the front. Slip the belt around the drum, reattach the front , and then finish positioning and tensioning the belt once the block is out of the way .

I went to repair the dryer belt only to realize that it was jumping off the pulley(edge was worn away). If you are replacing the belt, make sure your pulley is good before you order your parts. I ended up having to go to lowes and make a pulley!
Works great though.

We took off the front of the dryer and saw how the new belt needed to go on. It took myself, my daughter, and my husband to get the belt in place and the drum aligned. Once that was done, I put the front of the dryer back on, this holds the drum in place. After that, we sealed the back of the drum like the instructions stated, turned it on, and it worked. We were a little concerned with the instructions stating if the drum was not sealed properly it could cause "fire & death". We kept checking the dryer throughout the evening... no fire, so we were very happy to have done this repair ourselves. Thanks. I would not have tryed it myself except for the positive comments on your site when I looked to order the part. They were correct, it was easy to do and saved us a lot of money in repair service. It also showed my 23 year old daughter how easy it is to some things yourself. :)

First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

I replaced it

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

Ordered belt, received it two days later. It was a perfect fit.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.

It was easy to remove the lint trap first, then the front dryer panel. The drum easily was removed and installing the new belt was a little tricky because the belt had to be mounted onto pulley while holding the drum in place. I had a little help from a friend to help me stabilize the drum as I placed the new belt. Once on, it was easy to re-install parts in reverse and have dryer working again.