Models > AED4370TQ0 > Instructions

AED4370TQ0 Admiral Dryer - Instructions

Jump to:

All Instructions for the AED4370TQ0
106 - 120 of 768
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Marceline from SAINT PAUL, MN
Parts Used:
W10874409
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The lint screen had a hole
Just slipped it in place
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from GERBER, CA
Parts Used:
WP3977456
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
start switch replace
i could not perform the repair because despite using the proper id numbers, i received the wrong parts from kenmore three times in a row. now i am trying to return the wrong parts which cost me 120.00 for the start switch, and the knob for the switch, so far. the switch was 40.00 the simple plastic button was (wrong) 40.00, and the wrong unidentifiable part, suposedly correct one, which also was 40.00. this, with the original 40.00 wrong switch amounted to the 120.00 that i am still trying to have returned. otherwise, the fix should be quick and simple, o yeah, its been three months.. you tell me if i am satisfied....
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from SYRACUSE, UT
Parts Used:
279827
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Mother was frozen up
I followed the video. So easy..
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet A. from NACHES, WA
Parts Used:
W10874409
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
THE FILTER SCREEN MY MY KENMORE DRYER WAS GETTING RAGGED AND SHARP AS IT PULLED AWAY FROM THE FRAMEWORK. I KEPT CUTTING MYSELF PLUS WAS CONCERNED THAT SOME OF THE LINT WAS WAS NOT BEING FILTERED OUT.
IT WAS EASY, TOOK OUT THE OLD ONE AND PUT IN THE NEW ONE!! ANY ONE COULD DO IT.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from N RIDGEVILLE, OH
Parts Used:
W10861521
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
replace dryer door gasket
Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary Y from ROCKVILLE CTR, NY
Parts Used:
W10874409
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Corner of old lint filter screen broke away from its frame.
Went on-line Chat and described my problem to a very professional and patient representative who requested the necessary information needed to replace my filter. Note: Due to the age of the my dryer, Sears no longer had a replacement. I'm thankful that this site was able to accomodate my need.
The repair, or should I say replacement, was as simple as pulling out the old filter and replacing it with new. Only tools, my two hands.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
diora from ROCKFORD, IL
Parts Used:
W10861521
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
wore out gasket
removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Wilton, CA
Parts Used:
279827, 239087
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Dryer made loud rumbling noise and then shut down
It had been making noise for a week and I bought the two drum support rollers hoping that was the problem. It wasn't as the dryer started shutting down after a few minutes of running. I opened the top of the dryer and removed the 2 screws holding the face and door on. I removed the face and disconnected the door switch wires and released the drum belt by pushing on the idler pully. I then removed the drum straight out the top. I then put a wrench on the fan on the back of the motor and unscrewed it and then released the two holdown clamps on the motor and removed the motor. I had to make a couple of wiring modifications for the new motor but the instructions and connectors that came with the motor were perfect. I put everything back together and plugged the dryer back in and tried to start it and .... Nothing. I forgot to reconnect the door switch wires. Fixed that and the dryer now runs as good as new and makes no noise at all now (almost anyway). It should be good for another 10 years easy.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jay from Manchester, MO
Parts Used:
WP3406105
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken door switch meant dryer was shutting off thinking door was open when it wasn't
pop off the lid, replace the switch. (in meantime, while waiting for replacement switch to arrive, shorted switch wires together to fool dryer into thinking door was closed)
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
peter from portland, OR
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Broken belt
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
scott from seymour, IN
Parts Used:
279816
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
2 problems dryer ran but wouldnt heat second was the door switch spring broke iwas using a plastic clampt o hold the button in so the dryer would run
first with the dryer unpluged ,i removed the wires from the upper thermal cut off ,then with a nut driver i removed it . replaced it with the new one and reattatched the two wires then the same on the bottom thermal . to replace the spring i removed the two screws pulled out the switch and spring at the same time ,removed the broken spring and replaced it onto the switch then placed it back into the dryer and replaced the screws.! everything worked like it han never been broke! my wife is verry happy!!!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from East Durham, NY
Parts Used:
WP3977767, 279816
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Dryer would not start
I put in the new parts but it still did not work, Turned out the Thermal Fuse Blew,removed the two wires and clipped them together and the Dryer worked, have to replace the Thermal fuse and everything will be OK.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Claudia from NEWBURY PARK, CA
Parts Used:
WP3406105
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer wouldn't start
Watched video, followed instructions. Works perfect.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from PITTSTON, PA
Parts Used:
279827
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dryer makes squealing noise, finally the motor seized up.
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chad from Yukon, OK
Parts Used:
279816
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
Dryer not heating
I removed all the screws to the back panel to gain access to the inside. checked all thermostats and fuses for conductivity (0.001 ohms) resistance. noticed the thermal cut off fuse (thermostat) was showing no conductivity (infinite ohms or OL). FYI the thermal cut-off kit I purchased included both the thermal cut-off fuse(why this is called fuse is a lie its actually a thermostat) and high limit thermostat. I'm seeing alot of users purchasing these seperate but it isn't neccessary. You might need some wire strippers with a crimper though to install everything.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the AED4370TQ0
106 - 120 of 768