DU801DWGQ2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water in bottom of dishwasher
Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Hendersonville, NC
- Parts Used:
- 676413
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dish was broken and needed to be replaced
The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Woodstock, IL
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking where motor drive shaft enters pump
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Soldotna, AK
- Parts Used:
- WPW10509257, WP596669
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking during cycle
I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from San Jose, CA
- Parts Used:
- WP8528862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leakimg a lot of water from under door.
Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Eight Mile, AL
- Parts Used:
- W10844024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Wouldn't fill with water
Instructions very easy to follow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sacramento, CA
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Stopping in the middle of cycle. Finally quit completely.
Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Woodward, IA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaking in lower front door area
Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SELKIRK, NY
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad door switch
i took the inside door off and took the 2 switches out and replaced them; not too difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jagannathan from Centreville, VA
- Parts Used:
- 3380371
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Wheel
I removed the top dishrack by removing the front clips(stops) on the tracks. Then I removed both tracks by removing the back stops. Then I replaced 7 wheels. Then I replaced the tracks, dishrack and the front stops. The whole job took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Republic, MO
- Parts Used:
- WPW10082894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Heating element would not heat
I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Mt. Carmel, TN
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Roller came apart or broke apart
Take the stop off the end of the roller assembly, remove the old roller and replace with the new roller. Replace the stop assembly. Your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from grant park, IL
- Parts Used:
- 676413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dish washer soap drawer would not work
we followed your instructions submitted via e-mail and they worked out just fine....thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Little Rock, AR
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top of the Soap Cap Latch was broken
The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!