DU840SWKX0 Whirlpool Dishwasher - Instructions

The panel was removed by removing the lower screws and lifting the panel out. The old panel had a wood insert to match the cabinets in the kitchen. I removed the upper plastic piece holding the wood in place and slipped it out. I inserted this into the new access panel and attached the upper plastic piece to hold it in place. I detached the metal vent piece from the bottom of the old access panel and snapped it into the new panel. I then slipped the metal vent over the lower screws and tightened them. Finally I inserted the upper screws and tightened the panel into place. It took less time than I expected and only required a nut driver and a screwdriver.

after that every thing went very well

Getting the dishwasher out was easy. Getting to the impeller was easy. Getting the impeller off of the motor shaft was the difficult part. I had to use my Dremel tool with lots of cutoff wheels to cut the impeller off of the motor shaft a little piece at a time. It appeared to be rust on the motor shaft that was causing the impeller to not come off. There is not much room for the Dremel so be careful not to nick the pump housing or cut into the motor shaft. Keep the vacuum close by to clean out the plastic impeller shavings. Clean the rust off the shaft with steel wool, fine sandpaper etc. Assembly was easy once everything was cleaned up.

I entered the make and model of the dishwasher into the parts store. The part was located and ordered. Received the part a few days later. Fast, efficient way to go!

Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

New one snapped right into place.

I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.

After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

Part arrived in 48 hours. Had to pry apart the two piece assembly of the damaged item. Snapped the replacement in place and fastened it to chassis with two machine screws

After getting the pump and motor off of the dishwasher, I used a screwdriver and small hammer to break the impeller off of the motor shaft. The shaft was corroded and pitted real bad but this doesn't matter because the shaft of the impeller actually goes through the seal. I removed the old seal and replaced it, slipped the new impeller back on the motor shaft and put the pump and motor back on the dishwasher. Our local repair man told us it couldn't be repaired and we needed a new dishwasher. I had the parts from Part Select in 2 days. The parts were less than $35 dollars and repair very simple. The person on your comment section on how to fix it that said to break the old impeller off of the shaft made the job very simple.

No tools required except possibly a small screwdriver to help remove stop in end of rack; part easily installed by hand and stop re-inserted. Finished in several minutes. Thanks!

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Crazy Glued it together until we received the new part, but it fell off again. My husband installed the new piece and said it only took him about 2 minutes. You just take off the end cap and pop in the new piece and adjust to match the one on the other side of the rack. He said it was extremely easy and no tools required.