DP8700XTW2 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WP717273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shreveport, LA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replaced four lower rack on a whirlpool dishwasher.
I prayed old wheel assembly’s off with the claw end of a claw hammer. Carefully snapped on the new assembly’s which were a little tricky to align. Went well, took about 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rochester, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Rack Was Rusting Out
Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from CLEVELAND, OH
- Parts Used:
- WP8066018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Soap door wouldn't open.
I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ned from Mauldin, SC
- Parts Used:
- 4317933
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dry rotted/missing plastic wheels on bottom dish rack
Popped the old ones off and replaced them with the new set. No tools needed. Just clipped the new ones on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from JUPITER, FL
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from GREENVILLE, MI
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
all of the old rollers were missing.
the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from BERKELEY LAKE, GA
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from ENDWELL, NY
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replaced roller assembly with missing rollers with new Tandem Rack Roller
Looked at existing assembly and snapped on new one, duplicating existing installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurence from Sherman Oaks, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rear roller frames became warped & made it hard to put the rack in.
Simply snapped out the old ones and snapped in the new ones. Worked like a charm. Glad you had the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricker from KESWICK, VA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
noisy
watched a video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dubuque, IA
- Parts Used:
- WP8066018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
soap dish door does not always pop open
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Was this instruction helpful to you?
Thank you for voting!