DU9700XR4 Whirlpool Dishwasher - Instructions

Turn off power at breaker
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Remove completely the old one and installed the new entire kit.

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.

I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now

took off the old wheels and put on the new.couldn't be easier.

Replaced the lower seal, drain impeller,chopper blade, and wash impeller. Problem is still not solved but the inner parts have been replaced. Only thing logical next is the check valve. Unit cycles well and if I turn the dial to just before the rinse cycle and watch, I do see water draining from the unit...Of course while replacing these parts, I checked other things and found a loose spring behind the front cover. It can be seen on the diagram as it is part of the detergent door mechanism (or so I believe), but it is not clear on where the spring actually connects to.

Watched "Steve" install the drain and wash impeller kit and then I did it.

My husband took the dishwasher apart three times, it was a little frustrating, but was worth the $50 part because it made his wife, very, very happy! A dishwasher operating is on the top 5 list of favorite electronic items in our house.

I watched the video then followed the procedure accessing the impeller/grinder from inside the tub. Had I not watched it, I would have torn into it from the bottom by removing the motor, etc. with disastrous results. I was quite depressed when installation of the impeller kit did not resolve the problem. I remembered from the survey that 56% of problems were solved with this kit; BUT, another 24% found that the check valve on the discharge line was the problem. So I removed it and lo and behold, it was partially plugged with broken pieces from the old impeller. The 1 page sheet that comes with the kit is simply a diagram of the parts included, there are no instructions ---- watch the video!!! All said and done, my experience with PartSelect was first class. They are 5 Stars in every category and I would highly recommend them.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!