WDF730PAYM1 Whirlpool Dishwasher - Instructions

removed and installed cords with screw driver

I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).

By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.

Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.

I noticed the spay arm had some lose. I removed the old spay arm and noticed that the locking nobs broke off the arm and it would not tightly attach to the water outlet in the bottom of the dishwasher. I looked up the dishwasher model number, several diagrams of the dishwasher were offer. I review them and selected the Spay Arm part. It came in 3 days. I attached the spay arm and it snapped into place. Problem solved for less than $60.

If your are just a tiny bit "handy", you can do this job in about 30 minutes for $30. The rubber gasket comes off very easily from its location, just pull it off, than, using a small piece of wood, I used a shim, insert the new gasket in, an inch at the time, all around the frame. No more leak, and probably over $150 savings. A plumber or repair man would have charged $90 just to drive to my house, plus part & labor.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.

Watched a video and read through written directions.
Did not need to pull out the dishwasher from the cabinet.

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done

My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!

Remove any pieces of the rear stop by prying it off the end with small flat blade screwdriver. Make sure rack is fully on the roller tracks and then carefully push the new plastic end piece onto the rack. Be sure to orient it correctly by checking the end piece of the other rack.
I ordered two and replace them both at the same time.

went to utube

Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

Unplug (disconnect power)
Shut off water
Disconnect water supply line
Clean up any water spills
Remove clips holding air gap hose and wire inside cabinet.
Open dishwasher door and remove two screws that secure dishwasher to cabinet (these are at top of door opening).
With door closed, remove panel under door (this has a screw clamp on each side that requires a quarter turn to release).
Lower the dishwasher as necessary to provide vertical clearance by adjusting leveling legs.
Pull dishwasher out from under counter (grip from under door) far enough to expose springs (one on each side). Take care to feed all connecting lines smoothly through cabinet opening.
Note how existing springs are installed.
Install new spring in the same fashion as the old spring was installed.
Test the door operation.

Push unit back under counter taking care to draw connecting lines back through cabinet opening.
Readjust leveling legs as needed.
Reattach unit to counter top.
Reattach water supply and open valve.
Check for water leaks both at valve and under unit, fix as necessary.
Replace panel under door.
Replace any clips inside cabinet.
Reconnect power

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

Watched a video via website. I'm 74 years old but it looked so easy I thought I'd give it a try. I DID IT!!! It was a fairly easy repair. I did run into one problem since my dishwasher is 16 years old. I had a problem with the connector but I swapped out the connector part on the new one with my old one and it worked. I'm back in business!!! Just find a video on the repair and you too will see how easy it is to replace.