WDT710PAYB0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from LAMAR, IN
- Parts Used:
- W10542314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water leaking on bottom left of door
Just pulled the old gasket off and started on the bottom of both sides of the door installing the new gasket and finished at the top in the middle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from SCHENECTADY, NY
- Parts Used:
- W10542314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
leaking water out of lower left corner of dishwasher door
removed old door gasket, cleaned gasket groove, and than started new gasket in both corners working my way to middle top of door, made sure gasket was in groove properly w/my fingers. problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sallisaw, OK
- Parts Used:
- WP717273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes would'nt come clean or dry from torn boot
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Temperance, MI
- Parts Used:
- W10542314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Door Gasket.
Fast,smooth,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from POWDER SPGS, GA
- Parts Used:
- WPW10503548, W10827631
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace black access panel on Whirlpool dishwasher (model WDF520PADM7)
I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).
By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.
Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.
By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.
Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from BLUE SPRINGS, MO
- Parts Used:
- WPW10195175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Soap dispenser broke
Watched a video via website. I'm 74 years old but it looked so easy I thought I'd give it a try. I DID IT!!! It was a fairly easy repair. I did run into one problem since my dishwasher is 16 years old. I had a problem with the connector but I swapped out the connector part on the new one with my old one and it worked. I'm back in business!!! Just find a video on the repair and you too will see how easy it is to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Hollywood, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water not heating,dishes not drying
My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Southbury, CT
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door is designed to stay in place when opened. Door should hold partial or fully open.
Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Baltimore, MD
- Parts Used:
- W10542314
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Water leak at the bottom left corner of the door
If your are just a tiny bit "handy", you can do this job in about 30 minutes for $30. The rubber gasket comes off very easily from its location, just pull it off, than, using a small piece of wood, I used a shim, insert the new gasket in, an inch at the time, all around the frame. No more leak, and probably over $150 savings. A plumber or repair man would have charged $90 just to drive to my house, plus part & labor.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from Humble, TX
- Parts Used:
- WPW10477552, W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The green "Clean Light" was staying on after shutting down in the middle of the cycle. I put it in troubleshooting mode and found out it was the heating element.
Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BEND, OR
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Top rack rear stop broken
Remove any pieces of the rear stop by prying it off the end with small flat blade screwdriver. Make sure rack is fully on the roller tracks and then carefully push the new plastic end piece onto the rack. Be sure to orient it correctly by checking the end piece of the other rack.
I ordered two and replace them both at the same time.
I ordered two and replace them both at the same time.
Was this instruction helpful to you?
Thank you for voting!