DU1014XTXD5 Whirlpool Dishwasher - Instructions

First i remove upper rack held in by 2 clips at end of metal tracks. Compress inside clips and pull up then slide rack out of tracks.Then remove bottom rack just pick it up.Then i removed bottom sprayer by unscrewing center thumb screw. Then removed feeder tube for top sprayer held in place by 2 ea. phillips screws one on celin of tub and one at back of tub. Move tube to the right which unlocks it and remove. This has to be done to expose 4 ea. star screws. Remove screws and pop screen cover off. You have to take a towel and soak up water to expose bottom of inlets and outlets for water. You will then see the chopper blade with metal screen behind it. It is held in place with on star screw to the left of round top cover. Remove cover and pull on chopper blade which will release it from fingers mated from shaft to chopper blade .While pulling on chopper blade toward front of dishwasher pull up on metal screen it will come out. Clean all food particals out i used a shop vac worked well. Be careful not to drop screws in water inlets. The plastic shaft was broken in half by a piece of dental floss wrapped around shaft. I hope this helps it was not that diffacult just hard to work over door.

Make sure you order 2. One on each side

I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .

Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

Removed first part of the broken part from the top rack of the dishwasher from below.

Removed the screw from the bottom of the sprayer arm to release the second half of the broken part.

Threaded new part in sprayer arm and replaced screw.

Attached part to top rack of dishwasher from below. This part was difficult. (The part appeared to be a little larger than the original.) It was a two person job, one person pushing down on the rack and the second pushing upwardand inward on the part it click to click it into place. Dishwasher now works great.

This procedure assumes that the DW water connection and drain are flexible. Remove Phillips head screws (2) mounting top front of DW to underside of counter. Grasp door and gently coax DW outwards approximately 1 foot. WEAR SAFETY GOGGLES. On RHS check lower end of door spring and note in which notch the spring sits. On RHS, grasp white plastic connector ("hinge bushing", with spring looped around one end), stretch the spring while carefully lifting other end of connector up, out of slot in door hinge lever. Pry door hinge lever 1/8" away from DW body while sliding friction sleeve over its end. Work friction sleeve past hinge hook, past wider section, into narrower slot (about 2" from end of hinge hook). Raise door to closed position. Insert and hold lower (90 degree) end of spring into the same notch that it was originally in (mine was in the 5th from the front). Loop the door end of the spring into one end of the white plastic hinge bushing, then insert the other end of the bushing into the door hinge lever's hook while stretching the spring. It does not require much strength. CAUTION: If the lower end of the spring is not properly inserted and held in the notch, it can pop out and possibly injure you! Repeat for the LHS. Push the DW back in place, and reinstall the two mounting screws.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.