DU8100XT3 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eieen from Methuen, MA
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end loop on each end of spring broke off
Looked at right side of dishwasher to see how it was attached and did the same. Spring was slightly shorter than the original and the loops are not a sturdy. Will see how long it last.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Las Vegas, NY
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audrey M. from Attleboro, MA
- Parts Used:
- WP304204
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper spray arm broke off.
Had to clip the part onto the upper rack. It was a little tight at first, then all of a sudden it just snapped in. Voila, as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Bellevue, OH
- Parts Used:
- WP304204
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Remove/Replace Upper Spray Arm
Tried using my hands to bend back the locking plastic connectors enough to get them onto the metal upper storage rack;was afraid of breaking the connectors so I used my utility tool needle nose pliers to give me leverage. This time I was successful. Believe me,it was frustrating for what seemed a long time. No,for me it was not easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Sebring, FL
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Detergent door would not spring open-spring was broke
Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve J from Brookville, IN
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rubber on the nozzle cap fell off
Unscrewed the old one and replaced it with the new one. My wife actually ordered this Pat and repaired the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Powell, OH
- Parts Used:
- 675238
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher wouldn't drain
Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delano from Durham, NC
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring on dispenser broken
Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruby from Saint Marys, GA
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing part
screw it in then hook up the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Newton, MA
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door spring
Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald W from Austin, TX
- Parts Used:
- 303650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Wasn't getting any water into the washer
Turned off water and power. Used small nut diver to remove two upper screws from kick-plate, and loosen two screws in lower key slot of kick- plate. Removed kick- plate. Used plier to compress snap ring and remove hose to washer. Pulled off electrical connector. Used 5/6 wrench to remove copper water inlet. Used nut driver to remove two screws holding old valve. Once out removed the water connecting elbow from the old valve and installed it on the new valve. Reversed process to reinstall. Didn't even have to remove washer from the counter. My 25 year old washer is working like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Alton, IL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
One spring on a dishwasher door was broken
I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.
Was this instruction helpful to you?
Thank you for voting!