DP3000XRN0 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from JUPITER, FL
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from GREENVILLE, MI
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
all of the old rollers were missing.
the design of the new roller kit was a little different than the original. took a minute to figure the installation. all went well. the new roller assembly fit the 30 year old dish rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BRUSH PRAIRIE, WA
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replaced broken door spring
This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from ELGIN, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
my old lower dishwasher rack was rusted out and some parts broken.
Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some directions though.
ooks beautiful and works perfectly.
Could have used some directions though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from Jonesborough, AL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door spring broke
It took longer to take the 2 screws out than it did to put spring on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from St Johnsbury, VT
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower rack started to rust through coating
Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from VALPARAISO, FL
- Parts Used:
- 675659
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
water leaks. ordered the door gasket
when removing all the screws from the door gasket the dishwasher door and frame separates making reassembly not possible. you have to leave at least one screw on bottom half on each side, After all that the door would not close. I had to remove the new gasket and put the old one back on.
I need to return the gasket for credit
I need to return the gasket for credit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from JACKSONVILLE, FL
- Parts Used:
- W11169039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper dish rack broken tines
Swapped out the old upper dish rack with a new one. A video made the change simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from ENDWELL, NY
- Parts Used:
- 4317933
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replaced roller assembly with missing rollers with new Tandem Rack Roller
Looked at existing assembly and snapped on new one, duplicating existing installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dubuque, IA
- Parts Used:
- WP8066018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
soap dish door does not always pop open
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurence from Sherman Oaks, CA
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rear roller frames became warped & made it hard to put the rack in.
Simply snapped out the old ones and snapped in the new ones. Worked like a charm. Glad you had the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Dayton, TX
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishrack Tines were breaking off due to age
The rack came with pictorial instructions which were fairly veg, however they were to the point. The wheels snapped into place easily, and the center water transfer tube twisted off the old one and twisted on the new one just fine. It is a very good idea to keep the old one out to look at as a guide. There were no instructions on how to remove the transfer tube, I was lucky to have already worked on these before. After that it fits and works just peachy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annette from Grosse Pointe, MI
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken wheels on lower rack
This problem was making me NUTS! Every time I pulled the lower rack out, the rack would go off the track, threatening to break every dish, and I would literally have to half-carry the rack to move it in and out. VERY frustrating. No money for a new dishwasher, didn't want to pay for a whole new lower rack ($100). Then I discovered I could simply replace the wheel assemblies for less than $30 and no toold required. Yee-hah! It was literally a SNAP!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from Galloway, NJ
- Parts Used:
- 675611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old spring broken
after figuring out how to position the door the instructions were good
Was this instruction helpful to you?
Thank you for voting!