DU5000XL0 Whirlpool Dishwasher - Instructions

I pulled off the old clips and easily replaced them with the new clips and popped on the wheels.
I replaced 8 clips and 8 wheels in less than 15mins

Removed 5 or 6 screws replaced O ring,Srewed cover back on ,no more leak.

Removed dishwasher, take to garage, removed lower rack to gain access to top of motor unit. Used star socket wrench to remove upper screws holding top of unit in. Disconnect wires, drain tube and counter weight. pulled motor unit out from inside dishwasher and placed on bench. Proceeded to disassemble motor. Some things were obvious, others not so. replaced old worn out parts with new, used a little lube (Vaseline) in places to assist in getting seals back in place. Instructions were of little help need to pay close attention when tearing unit apart. Reassembled with new seals, installed motor and re-installed dishwasher...NO LEAKS!! Wife and I happy.

My dishwasher is an under the counter mounted model. No need to pull it out or move it. I used a screwdriver to remove the casing on the bottom of dishwasher. I then removed another piece that was just behind this casing. When this was done I could see where the springs were on either side of machine right in the front, - easy access. I followed the directions that came with the part. Three simple pieces came in clear bag. You first put plastic red end onto end of long metal piece and put it through the spring. Hook it into place by catching one end of spring. I took notice of how broken springs were hanging in machine and then replaced the new spring. I hung one end of spring on the hook and then pushed other end with red plastic piece through to catch the notch. (You can adjust placement for door tension considering there are at least three notches.) Space was tight so I held onto free end of spring with needle nose pliers and pushed it through with my fingers to the notch. I almost called a repairman to do this for me. That would have been an expensive way out of an extremely easy repair. ANYONE can do this as long as they have finger dexterity. I am thrilled to have a perfectly functioning dishwasher door again. The parts were perfect and much cheaper than buying from Sears or elsewhere.

There were no instructions with the part, but looking at the old rack it was simple to see how the parts should be assembled. Took the center part from the old rack, twisted off, and applied it to the center of the new rack. Snapped on the wheels and was done. Very simple assembly.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.

actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.

It was so easy , I first put one side of the clamp on the little rack area in the center of the upper rack then pushed the other side on. It took less than five minutes. No tools needed. Julia

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

I simply popped the old units off and popped the new units into place. Very, Very easy!!! No stress repair!

i followed all the directions and it went in very well,although i still had the leak,i visited the parts forum and got a reply that it was the pump outlet gasket,so i an very happy to have gotten some professional help and am glad i replaced the door gasket as it needed it anyway. thanks so much roy

The repair was very simple and covered completely in the instructions that came with the springs. However, I am writing this not so much to describe the repair but to give unsolicited praise to PartSelect. I pretty much only purchase online, so I spend a lot of time on web sites. This was probably the best shopping experience I have ever had (Google and Google Tool Bar were also involved). I found the site using Google, but then found my part in about one minute with the great diagrams. Checkout was incredibly easy and my parts arrived two days later and the door was fixed 30 minutes after that. I'm a customer for life!

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.