DU3014XL1 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOYCE from SMITHFIELD, NC
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The 6 rollers on the bottom rack of my dishwasher had fallen off over time. The rack wouldn't roll in or out w/o trouble.
I simply popped the old units off and popped the new units into place. Very, Very easy!!! No stress repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Schenectady, NY
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack rusting
This is the second time I have replaced a rack. You just pop on the new rollers and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Fremont, CA
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both door springs on the dishwasher door broke
The repair was very simple and covered completely in the instructions that came with the springs. However, I am writing this not so much to describe the repair but to give unsolicited praise to PartSelect. I pretty much only purchase online, so I spend a lot of time on web sites. This was probably the best shopping experience I have ever had (Google and Google Tool Bar were also involved). I found the site using Google, but then found my part in about one minute with the great diagrams. Checkout was incredibly easy and my parts arrived two days later and the door was fixed 30 minutes after that. I'm a customer for life!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Royal Oak, MI
- Parts Used:
- W10311986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
worn and rusted lower dishrack
First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.
Thanks for asking.
By the way, it was not blue.
Thanks for asking.
By the way, it was not blue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Schofield, WI
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The bottom dishrack was having areas that were breaking off and showing rust.
We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Fenton, MI
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels on bottom rack were broken
I layed the bottom rack upside down on the counter. Removed the old wheel sets and the new ones just snapped into position. I think the rack rolls better now than it ever did with the original equipment. I'm glad we purchase the Tandem Rack Rollers instead of a new dishwasher, it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from CHARLOTTESVLE, VA
- Parts Used:
- 675238
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
standing water in tub , not draining
removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from MAPLE VALLEY, WA
- Parts Used:
- 675238
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bottom of dishwasher retained an inch of water after cycles complete. Had to pump out dirty water before starting new cycle.
Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from REIDSVILLE, NC
- Parts Used:
- W11086533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed a tub sound shield
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Durham, CT
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original rollers were cracked and falling off
Unsnapped old rollers and snapped new rollers in their place. Very easy. The new set fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- grady from columbus, MS
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door spring broken
removed the bottom panel 4 screws,then replaced the new springs. I bought two and left the other one inside the panel saved $80.00 servive call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hank from Arlington, TX
- Parts Used:
- WP304204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm mounting clips broke
Simply snapped new spray arm in place. Took longer to get the soray arm out of the shipping package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Ft Lauderdale, FL
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
1 spring broke
removed the 2 screws that hold in the washer, pulled it out, with the door shut, removed and replaced the remaining spring , then went to the other side and did the one that broke off. then I reinstalled the unit. simple !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Clackamas, OR
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced the bottom rack
It was a piece of cake, just slapped together and slid it into place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Terryville, CT
- Parts Used:
- 4317933
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of lower rack wheels (rollers)
This job took 30 seconds to accomplish. The old wheel assemblies (4) just snapped off and the new wheel rollers just snapped in their place. No tools were needed. Extremely satisfied with this product. Wished I had performed this repair years ago!
Was this instruction helpful to you?
Thank you for voting!