66213299K112 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- WILLIAM from CLEARWATER, FL
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken wheel on adjuster
I looked up a you tube video of replacement for model and part. the video gave consise, clear and easy to follow directions. Using the video it took about 15-20 minutes to easily do the job.(I had difficulty seeing photos and reading printed directions that accompanied the part.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CONCORD, CA
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the roller wheel on the upper rack kept falling off, allowing the rack to fall..dirty dishes
tried to follow the instruction that came with the parts, to no avail? it would have been better to send a note that said good luck. the only part that helped was the part that said remove the old parts. after that is was just a fit and test, fit and test, fit and test, only because of my expert analytical abilities was i able to fit it all together. please draw up better instructions. it fits good and works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from HIGHLAND HGTS, OH
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The front roller on the right side of the upper rack broke off causing the the rack to tilt down off the track.
The instructions that came with the parts do not tell you how to remove the old adjusters from the rack. I found a video on YouTube ( Appliance Video.com) that takes you step by step on how to remove the old parts and how to install the new ones. The video made the repair easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kal from PHOENIX, AZ
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Existing rack adjuster broke and wheels came off.
Dismantled one side of dish rack and rebuilt that side with the new parts and then did the other side. Second side took a lot less time. IT took a while to figure out how to dismantle the old unit as the parts pictures you sent were not too clear in showing the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rob from HAMILTON, OH
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original rollers broke off
Read the instructions, removed old parts, installed the first side in about 4-5 minutes, second side about 3 minutes. Took longer to read instructions, than to repair. This is a great repair package, this appears to be a lot better than original parts. Fast service, very helpful customer service personal for return parts, as I ordered parts I didn't need. Thanks again rob h.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GILBERT, AZ
- Parts Used:
- W10712394
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
clip holding the rollers broke allowing one side to drop
The repair kit was easy to install, required a torque tip screw driver and thin flat head screw driver to remove the old parts. Took me 15 minutes start to finish. Simply follow the instructions provided with the kit. Nothing else needs to be said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from WHITEHALL, PA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Wheels kept coming off.
Took off the broken part replaced it with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana R from THE HILLS, TX
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
The wheel fell from the lower dish rack--the front left hand side.
We snapped the old one off --it did not break. We positioned the new one in the right place making sure that the slot in the middle matched up with the longitudinal wire of the rack and snapped it in place. EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G from BISMARCK, ND
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A wheel on the lower dish rack wheel assembly broke off.
Pry the old wheel assembly and snap the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from FRAMINGHAM, MA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wheel came off. Hub that held the wheel to the assembly got burned by heater.
Look at the way that 3 remaining Wheel Assemblies were attached to rack, Then pop off the offending assembly and attach the new one. Less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CANTON, MA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken wheel
Easy. Just watched video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from CHANDLER, AZ
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken wheels on top rack
The instruction included were pretty comprehensive. Also, it is not a difficult fix. Only thing I did different was install the release arm before snapping the upper part on to the rack. Liked the Phillips screw converter included in case someone does not have star bits for the screws. Returned the stop Clips, not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from BAINBRIDGE IS, WA
- Parts Used:
- W10712394
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper dish rack adjuster failed
Figured out what was worn and went to website to order replacement parts. Three days later the parts show up, I find the replacement parts are better build than the original parts. Took less than 30 minutes to repair and reinstall. Works perfect. Website was easy to use and the repair was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from DAVISON, MI
- Parts Used:
- W10712394
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pup per rack wheel hubs broke
I took the upper rack out set it on its side and followed the instructions that came with the parts. Then turned it on the other side and repeated the instructions. The nice part about the instructions is they they came with clear photographs of each step in the instructions. You could clearly see how the parts were suppose to fit. No guessing at all. Great job, who ever created them. I will not hesitate to but parts from this website and is saved in my favorites.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from LOVELAND, CO
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Upper rack wheels would not stay on. Axels were worn down from use.
Removed upper rack.Replaced both side rack adjusters purchased from Kitchen Aid. Replaced upper rack and checked for easy operation. They were made superior to original parts, what I would call an upgrade. The instructions are well written easy to follow and in order of completion. One word of advice, dont snap keepers in place untill you are sure they are in correctly. The picture quality could be improved to better assist anyone not used to doing these type of tasks.
D Burton
D Burton
Was this instruction helpful to you?
Thank you for voting!