WDF330PAHT3 Whirlpool Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rich from hamilton, MI
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
bad heater in qiuet partner 2
this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MCMURRAY, PA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
snap
Just snap it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Violet from SALEM, IL
- Parts Used:
- WPW10498900
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I noticed my top shelf in my dishwasher was not getting the dishes clean
I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from JACKSONVILLE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stop broke
Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from Ellicott City, MD
- Parts Used:
- W10876537
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher didn't drain.
Replaced the pump.That wasn't the problem --- if I had it to start over, I'd pull the drain hoses and run the dishwasher to see what water is flowing where. I had a clogged drain --- and maybe something else. Still working through the details.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACEY ANN from BRICK, NJ
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
DISHWASHER WOULD NOT FILL WITH WATER
Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from EAST GREENWICH, RI
- Parts Used:
- W10909088
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Tines where falling off old rack
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lena from Napoleonville, LA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Leak in hose
Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antony from Lakewood Ranch, FL
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Dishwasher was not firmly connected to the counter
Very simple repair when you're supplied with the proper parts. Their delivery time is exceptional !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Delaware City, DE
- Parts Used:
- W10445975
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
hose had a hole and leaked
I pulled the dishwasher out from the countertop rolled it to the side removed old clamps and hose installed new hose in kind used different hose clamps than provided turned up right pushed back in ran a cycle while looking underneath with a flashlight and saw no leaks and dishwasher has been back in use for a week now.Chris
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Beach, ND
- Parts Used:
- WP661566
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clean light was flashing and washer would not start
Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.
Was this instruction helpful to you?
Thank you for voting!
My dishwasher quietpartner ii was not cleaning my dishes. It seemed it was not heating correctly that the Hi temp wash or the heated dry.
I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Monterey, CA
- Parts Used:
- W10909088
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
just wanted to replace the upper dish rack - the pieces have been rusting through
no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Muskego, WI
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer would short-cycle and flash an error code - 7 blinks of the clean light -
The fault code suggests a problem with the washer's ability to maintain water temp. This could be caused by a failure of the tempurature sensor module, safety over-temp thermostat, or the heating element. First, I disconnected AC power at the Mains panel. I then verified that the heating element was indeed at fault by removing the dishwasher and disconnecting the leads to the heating element in the rear of the unit. I set a multi-meter to resistance and measured the element and found that it was electrically open, thus proving it was the part needing replacement. I then tested the replacement element and verified it showed low resistance. (Good). I then loosened the plastic retaining nuts with an adjustable wrench, removed the old element and replaced it with the new. The nuts were then re-installed and torqued with enough force to create a leak-tight seal as verified by pouring a gallon of water in the washer. I reconnected the leads and slid the dishwasher back into place and secured it to the counter with screws. I then turned power back on at the AC Mains panel.
Was this instruction helpful to you?
Thank you for voting!