DU9450XT0 Whirlpool Dishwasher - Instructions

Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes

A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.

I used a screwdriver to snap off the old wheel carriers. When Ito attached the new pieces the tray wouldn't close. It was too wide. The person at Part Select was most helpful and patient but I still couldn't get them attached so the tray would fit. Then this week-end I visited my daughter and looked in her dishwasher, not the same brand but I could see how they attached, came home tonight and was able to figure it our easily. May I say a visual would have helped but your sales person was excellent.

Dishwasher Stopped then only made a humming noise. Started with the Video on your site and it was quite helpful. I had trouble holding the drain impeller with the wrench. Used a drill to bore holes around the center and then broke the outer ring off to get a good hold on the center. Then was able to remove the bolt. The rest of the repair was easy. Something had caught the chopper blade and unraveled the spring. Replaced all the parts and it is working fine now.

Ordered the drain and wash impeller/chopper kit, which I received in 2 days. Great service. I watched the video on how to install the parts and the video was very clear and made the job seem easy. And it was easy, except for getting the impeller screw out. The impeller top was very brittle and pieces kept breaking off when trying to hold it with the adjustable wrench. Robo Grips didn't work any better. The only thing that finally got that screw out was a long handled socket wrench with an extension. You need the extra leverage if the screw is really stuck. Also note that the balls are definitely in the wrong place in the video. You need to remove them when doing the repair, then drop them back into the hole in the gasket/seal cover for the impeller after it is replaced. They will sit side-by-side if installed correctly. Turns out that the crunching/grinding noise was the chopper trying to chop up one of the clips that holds the silverware basket on the bottom rack. It was in many small pieces and had ripped up and split the impeller shaft.The dishwasher is back together and running perfectly. Thank you for very clear instructions on replacing the part and the quick delivery of the product.

My model was DU7600XS0. I disassembled according to the video and the parts diagram here. I found a piece of metal, a pebble, and a wrecked drain impeller. I cleaned out all the debris and began reassembly. I found that the chopper blade shipped with this kit has a lip and will not fit over the metal drain impeller sleeve on this model. It needs to, or else it will not screw together properly and the impeller will not be able to turn. My old one was undamaged, so I used that instead. Also, the large black wash impeller has a shaft that is longer than the original part and because of that, it would not screw on. Again, the original wash impeller was fine, so I used the old one. I replace the gaskets and screwed everything else back together. It works great now. No water is left after the cycle anymore and the sound it makes is back to normal. Money well spent on this kit!

Heard a grinding noise in our dishwasher one night recently while it was in the drain mode. Water wasn't draining out so I had to siphon it out with a tube, cup, and rags, then looked up information about the washer/dryer on the internet and found PartsSelect. I watched the repair video they provided and decided to give the repair a try. I began to remove all the necessary parts following the instructional video.
The hardest part of the job came early on, and once that was completed the rest of the job was a cinch. The center screw holding the upper impeller was the hardest part to remove. I tried to use the adjustable wrench on the hex shaped nut molded to the impeller while turning the screw, but that old screw was so tight I was afraid I'd strip the molded impeller nut.
I then tried a 1 inch nut without the driver attached to it but with a pair of vice grips clamped at about 45 degree angle on the 1 inch nut and set on the molded impeller nut while at the same time trying to remove the screw by putting the small nut driver through the top of the 1 inch nut and turning it. No luck there either. It would not budge.
By this time I was entertaining the idea of buying a new 5 to 800.00 dishwasher.
Well I had nothing else to lose except 5 to $800.00, so I reverted to caveman technology.
I ended up using a small chisel and wood mallet to get the impeller off the shaft. Since the impeller is made of a rubber like material, it came off easily in pieces using some careful strikes with the hammer on the impellers molded nut. When this was complete, I unscrewed and removed the filter housing.
The impeller screw, which was still in the motor shaft, and was removed 'after' this because there was no impeller or filter chamber in the way. There was a small space between the screw and the motor shaft since the impeller was removed from around that screw so I first tightened it a little bit, then finally was able to loosen the screw. You would think that screw had been super glued into that shaft but it finally came out. After that I removed the chopper blade and found that the spring attached to it was bent and had tore the shaft of the 'lower' drain impeller to pieces. After cleaning up the impeller pieces I ordered the drain and wash impeller kit from PartSellect. It arrived in a couple of days and the new parts installation went quickly.I was especiially relieved that the new screw and impeller went on without a hitch.
I didn't use the new shaft seal provided because it was a different height then the original seal and wouldn't allow the cover to the drain impeller to seat properly. The height of the new seal also caused the new drain impeller to push or spring up too high.The original seal looked fine so I used that and it worked just fine also. Started the dishwasher up for a test and it all worked flawlessly. No noise no leaks. This was my first washer dryer repair. Following the Part Sellect instructional video with Steve explaining while doing the removal of old and installation of the new parts was a breeze. SO, here's my conclusion. Folks, for under $50.00 I saved a lot of money and expect that I'll get at least a few years more use from this old dishwasher. Thanks again to PartSelect and Steve for your help.

My dishwasher quit working the week before Thanksgiving, and to say the least, my wife was quite concerned. I did not know what was wrong, until I found the info on this website, including a how to repair video. I watched the repair video on the website when I ordered the parts. Other than my wash arm being different from what was shown in the video, it went exactly as shown in the video. I'm glad that the video, and the bag with the parts told me that there are fewer parts than originally were installed on the original. The parts looked like they had been redesigned a little, and were easier to assemble. Overall, I will be getting any repair parts I need for other appliance repairs in the future from here. Thank you for making this experience as easy as it was.

The repair was fairly simple and made easier with an installation video. The repair went well and there's no more leak.

Initially, I was going to call a repair-person to fix the dishwasher, but decided to check and see what was available on-line. I was very surprised to find a video on YouTube for my specific model. Even more surprising was the relative ease to perform the repairs, after watching the video. I have the proper tools, so I disassembled, per the video and found the problem. I was elated to see how easy it was to order the parts kit. It came in three days, and within 1/2 hour after parts arrival, I had the dishwasher purring like a kitten. What an excellent service. If you can turn a screwdriver, you can fix your appliance, via these well-done videos.