DU9450XT0 Whirlpool Dishwasher - Instructions

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Remove completely the old one and installed the new entire kit.

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

The part arrived the next day with regular postage, outstanding service.

screw it in then hook up the hose.

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Watched your video

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

Replaced the lower seal, drain impeller,chopper blade, and wash impeller. Problem is still not solved but the inner parts have been replaced. Only thing logical next is the check valve. Unit cycles well and if I turn the dial to just before the rinse cycle and watch, I do see water draining from the unit...Of course while replacing these parts, I checked other things and found a loose spring behind the front cover. It can be seen on the diagram as it is part of the detergent door mechanism (or so I believe), but it is not clear on where the spring actually connects to.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

We followed the excellent video until we couldn't remove the outlet impeller because the motor shaft was not being held by the failed impeller. We drilled small holes around the impeller shaft until we could break off the upper part of the pump shell. Then we could hold the motor shaft with a vice-grip pliers by squeezing the shaft of the remaing impeller piece. We then removed the retaining screw and the rest of the impeller. Then evrything went well by following the video. There was still a bit of doubt because we discarded more old parts then expected but the machine now works well and we see no leaks.

Turned off electric to machine.Removed water with shop vac, Removed lower panel, removed drain hose from check valve and garbage disposal. using shop vac removed blockage from drain hose. Reconnected hose turned on electric cycled dishwasher. Didn't work. Turned off electric, removed water, removed basket, sprayer arm, pump cover, used a six point deep socket to hold impeller while removing 1/4 in. screw. Removed the impeller and found the problem.The lower impeller shaft is broke. removed separator, chopper blade and spring, removed pump cover and broken drain impeller and lower seal. Cleaned all old parts and installed new drain pump kit. Replaced spray arm , basket . Turned electric on, cycled the machine one time. Checked for leaks, replaced lower panels. Put away tools. Your video was very helpful. Your service was great. I received the parts the next day after ordering them. thank you. thank you.

I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .

Watched "Steve" install the drain and wash impeller kit and then I did it.

My husband took the dishwasher apart three times, it was a little frustrating, but was worth the $50 part because it made his wife, very, very happy! A dishwasher operating is on the top 5 list of favorite electronic items in our house.