GU1500XTLQ2 Whirlpool Dishwasher - Instructions

first things first. troubleshoot.... unit wont run. no l.e.d.s at all. Opened front panel and first thing I see is a thermal cutout mounted outside of printed circuit board. After using a multimeter to check for continuity, used a set of alligator clips with a common lead, thus bypassing thermal cutout. Viola, she worked. Ordered part after finding site with google search. Part was delivered in two days.

When my dishwasher stopped working I went to the local appliance parts store with the entire button panel. I explained my situation to them, and the response was that I needed a new control panel -$68 and a week wait. So I ordered it. When it came in I noticed it was missing a button for the rinse only cycle. The parts guy said that maybe it was a problem with the parts vendor and ordered another one from their other vendor. In the mean time I installed the new control panel just to see if I would get any lights (no luck). A week later the new control panel came in - still no rinse only button. I got my money back and went home to see what I could find online. I ran across PartSelect - saw several comments describing my exact problem, and ordered a new fuse kit ($15). I put the original control panel back in, put in the new fuse (which took only 2 days to get to me!) and sure enough - problem solved.
Thanks PartSelect you have a great site with lots of useful information!

Steve in Colorado

Removed old part and replaced with new part

Opened dishwasher door,removed 6 Torx screws, changed out panel, replaced screws. VERY SIMPLE

just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks

Just snap in the pivot. No tools required. Be careful how you put it in because you could end up snapping it in half. Slide the shelf leg into the pivot first then snap the pivot on the rack.

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again

Easy to do. Less than fifteen minutes total and only tool required was a screw driver. Simply pulled out the old gasket by hand and then pressed in the new one with the screw driver. Anyone could do this.

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

I removed broken mount by gently bending tabs, pressed new mount into upper dish rack, attached the spin arm and secured the mount with the screw.

A snap---it took less than 2 minutes after only a two day turnaround from ordering the part to receiving it at home..

Fantastic service. Thanks!!!!

To perform this repair do the following:
1.) Turn off power to the dishwasher
2.) Turn off water, disconnect the water supply and drain using adj. wrench and/or nutdriver, remove any contents from inside
3.) Remove screws (2) from underside cabinet, remove kick plate from bottom by removing two (2) screws there, pull out washer gently providing slack to drain hose and water line
4.) Gently place washer on side, do not invert or lean on the front side, water may enter control panel and damage it
5.) Remove the water line from Inlet valve using adj. wrench
6.) Disconnect both wires from solenoid.
7.) There is one metal screw holding the valve in place, remove it with a nutdriver, slide valve assembly out.
8.) Remove the 90 degree brass angle fitting from old valve, this may require some effort. Using thread tape, install fitting on new valve assembly.
9.) Replace parts in reverse order, using thread tape on any additional water line fittings requiring it, restoring water and power last.
10.) Run a test wash and check for leaks.
Hope this helps, it did appear to fix my problem.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

Took me longer to find my tools than to do the repair. DId have to call the PartSelect 800 # while making repair but woman there read to me a note in their system about a redesign of the replacement part that explained exactly my question. She was VERY helpful. I will not be calling the appliance repairman again!