DP3000XRN2 Whirlpool Dishwasher - Instructions

A VERY easy repair! I simply pried off the old wheel assemblies with a screw driver and popped on the new ones. I was a little concerned about the new ones fitting correctly as the dishwasher is over 25 years old, but after a week they still work fine. An easy fix to an annoying problem....wish I had ordered these ages ago! Bottom rack of my dishwasher now rolls in and out like new (instead of the the few remaining wheels constantly falling off!) Very happy I ordered these and delivery was quick.

Unscrewed the old one and replaced it with the new one. My wife actually ordered this Pat and repaired the dishwasher.

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

Had to clip the part onto the upper rack. It was a little tight at first, then all of a sudden it just snapped in. Voila, as good as new.

I unsrew the faucet head, and attached th e adapter

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install