MDBH945AWQ3 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Erik from Doral, FL
- Parts Used:
- WP6-917642
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Original part was worn out. It would not turn.
The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Burlington, MA
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking do to heating element decay.
1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from SAN FRANCISCO, CA
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Soap not dispensing
I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lake Zurich, IL
- Parts Used:
- WPW10192799
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishes not clean
with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Denver, CO
- Parts Used:
- 99002780
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Lower basket wheels fell off and were melted
Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Mapleton, UT
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher got the dishes dirty not clean
My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Deltona, FL
- Parts Used:
- 99002838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
handle broke at pivot points
Turned 120 v breaker off at power panel, removed 8 torx head screws from door panel removed old handle and snapped in new, replaces screws, flipped breaker back on. About 10 minutes tops using a battery driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Longmont, CO
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dispenser door broke
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST NEWTON, PA
- Parts Used:
- WP99003446
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher door would fall open
I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fayetteville, GA
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper wash arm would not turn.
Snapped the old part out and snapped the new part in.
It was a piece of cake.
It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTINE from SHORELINE, WA
- Parts Used:
- WP99002837
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
handle broke
unscrewed the fasteners removed the handle and lock unit replaced the handle, replaced the fasteners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Wheaton, IL
- Parts Used:
- W10280784
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack had rust spots.
You just remove the old unit and set in the new unit. the wheels were already connected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joann from Queensbury, NY
- Parts Used:
- 99002780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
New Wheels needed on dishwasher tray
Very easy after watching the video. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nora from Wilmington, DE
- Parts Used:
- WP6-918873
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
bottom of silverware basket broke
received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCHESTER, MA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking door
easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well
Was this instruction helpful to you?
Thank you for voting!