MDB8959SFZ4 Maytag Dishwasher - Instructions

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

Removed the inner panel, remove electrical connection to dispenser, remove dispenser, metal tabs that hold it in, are a bit hard to pry metal tabs, and when installing net dispenser tabs are also a little difficult to pry tabs to install but doable. So far works like it should.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

I took the inside door panel off so I could remove the top electrical panel. That was a matter of six screws. Once they were removed, I was able to reach in and unplugged the control panel. Mounted the new one and plugged it in and replaced the inside of the door with a six screws. This was a very easy replacement.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

1. Remove front of door with torx screws around inside top and sides of door.
2. Unclip and remove plug with two wires for dish soap solenoid. You may have to lie on your back or use a mirror to see the location of the small clip retaining the plug.
3. Unclip and remove dispenser module. Here's the rub: the clips used to retain the unit in the door panel of my dishwasher are tabs cut in the stainless steel cut-out and rolled back at a 90 degree angle to retain their springiness. They seat against the back edge of three plastic ridges along the top, bottom and one along each side of the dispenser module. The key is to remove the module without permanently bending these tabs, thereby losing their springiness and destroying their ability to clip tight against the new module to hold it in. I had some success slipping 3 pieces of flashing under the stainless tabs along the top and sides of the old module, allowing the plastic retaining ridges to ride under the tabs all together and move forward to disengage the clips without permanently bending the tabs.
4. Reassembly is just the reverse.

My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

pushed the new retainers in the holes and we are set to go

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

These wheel assembly that came on the lower rack of my dishwasher were junk! They started falling off within 6 months. I put them back on to the point that the pin in the center of the wheels would no long stay in place, thus the frustrating situation of the wheels falling off often.

Assembly was easy peasy!