MDB6702AWS41 Maytag Dishwasher - Instructions

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

I removed the old door seal -- it just slips right out. Then I inserted the new door seal. One thing I noticed on the old door seal and also in your photograph is that the last inch or two of the seal on both ends is kind of sliced in half perhaps to make it fit better in the corner. But we decided not to cut it yet and have been using it uncut as it arrived in the package. It is working great! No leaking! So we're not going to cut it. Thank you for offering this great service. It saved us a lot of money since we didn't call a repairman.

Remove inside cover and eight screws. Unplug two electrical connections.

Impeller bolts to plastic chopper mount which is screwed to the top of the motor. Threads on chopper mount were stripped causing impeller to not spin fast enough (replacement mount, which is part of the chopper kit, is metal). Installtion was not difficult.
You have to reach underneath the washer and wedge a screwdriver on top of the motor to hold the shaft from moving.

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

First I removed the torx screws halding the inner door panel on. I then seperated the door panel from the door and removed the latch assembly and disconnected the switches from the latch. After installing the switches on the new latch I replaced it between door and inner panel. Finally I replaced the torx screws and was finished.

Repair was fairly easy. There are 11 screws You have to remove then simply unplug the electrical connection from the door latch/switch and plug in the new one line up the screw holes tighten them down and your in business.

Pretty easy job. You need torx tips for your screwdriver. An electric screwdriver got all 8 or 9 screws out of the door panel in about 60 seconds, separated inner door from outer door, pulled out handle assembly & disconnected wires, attached wires to new assembly, screwed it all back together. Be prepared... the handle will break again. It's just a bad design by Maytag. This Maytag model is so bad the company discontinued it. Beware of the control panel getting corroded from steam & failing. If replacing this panel, make sure you seal where the cable goes into the touchpad with some kind of waterproof glue, nail polish remover, or sealing tape so it doesn't happen again.

1) Turned off the power

2) I removed the screws on the plastic door.

3) The latch/handle assembly was right there.

4) I noticed that white and black wires fed each side. I noted which side did the black feed and the white feed.

5) I took a pair of pliers and held the white wire brackets and pulled the metal parts off. This is where the time took.

It took about 2 minutes per side.

6) I then slid the new metal parts in the white brackets.

7) I screwed it back.

8) Turned it back on!

9) Works great

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Turn off the DW power (pull the fuse or turn off the circuit breaker) Open the dishwasher door. Remove the torx screws around the periphery of the door inner panel. Lift up the inner panel far enough to get at the door latch. Lift out the entire door latch assembly. There are two wiring connectors attached to microswitches on the latch assemby. Remove the connectors. The connectors were pretty tight, so I needed pliers to pull the connectors off the switches. Discard the old latch. Get the new latch, and plug in the connectors (keep track of which wires go on which side). Lay the latch down in the door so it lines up with the mounting holes. Lay the cover back down, start each of the torx screws into their threaded holes, then tighten them all. Don't over tighten. Turn power back on. Job done. It almost takes as long to type it up as it does to make the repair.