WC284 Maytag Dishwasher - Instructions

had to remove the iner door plate and remove the main switch or latch to get to the micro switches witch one had over heated over time,it is working like new at this time.

Firstly, I'm a 58 year old female and this repair was relatively easy for me, thanks to all the marvelous instructions on this site from others who made this same repair. Like the others, I removed the four lower screws on the INSIDE of the door along either outer edge. Before that, in error, I removed the four screws along the very bottom of the door, big mistake, hard to get them back in correctly. Removed the door panel and took out the 6 nuts from the dispenser cup, slipped the electrical clip thingys from the posts by slightly wiggling them straigt off, remember which color goes where. Cleaned the area around the old gasket and reattached the new gasket and dispenser cup. This was a little tricky holding it in place from the inside while using the nut drive on the outside. Whew! That was the hardest part for me. Thanks to all for the previous detailed instructions. I now have really clean dishes! Yay! Great feeling of accomplishment.

Replaced whole assembly

Remove lower cover plate below door. Remove broken spring with needle nose pliers. Place plastic insert into upper spring loop and loop into hole on right spring hinge. Grab lower spring loop with needle nose pliers and insert through hole in lower frame base. Reinstall lower cover plate.

I removed four philips screws to remove the front door panel. Next I removed the screws holding in the detergent cup. Removed the two electrical wires from the cup release. Reveresed the process to install the new detergent cup.

removed retaining nut and replaced

This dishwasher is over 20 years old and still works well. The door springs broke and the skematic shows 2 springs on each side. The spring kit only includes one spring for each side which is the primary spring. Removed the bottom access panel, shut off the water line and removed the water line. Removed the top screws which lock the dishwasher in the cabinet and pulled forward about 6 inches to fully expose the springs. Replaced the two big springs, one on each side and adjusted for maximum pull of door. The second small springs were not necessary. Pushed unit back into the cabinet, connected the water line and tested for water leaks. Cleaned and replaced access panel and the door is light as a feather.

First of all, ordering the parts from PartsSelect.com was very easy to do, I found and paid for the part in about 10 minutes with only the model number.

Removed the screws holding the old flange. Pulled it out and put the new one in its place. Installed the screws.

After I was finished I looked at the instructions. I'm glad I didn't look at them prior to starting. They were actually confusing.

I removed the access panel and it was right there. one screw - disconect the wires & it was out. then right back in - access panel on, and done.

I removed the 4 lower Phillips head screws on the lower inside of the door.(thanks to a tip from Robert) This removed the front panel allowing access to the detergent cup. I removed the 6 screws holding the detergent cup. Removed the old detergent cup and gasket. Installed the new cup and gasket and reinstalled the front panel. Amazingly easy. Now it's on to my stove. I'm hooked on your website

Easy repair, I put small marks under the counter to make sure the dishwasher went back in the same spot for easy screwing back in

Mice were living behind and on top of the dishwasher and destroyed the pad. Had to throw it away. Ordering you was easy, and the pad fit perfectly.

Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.

replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.

remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.