WC284 Maytag Dishwasher - Instructions

First, let me say that the parts arrived really fast,--thnaks for the great service!

First I removed the screws inside the door edges. This releases the front door panels allowing access to the detergent cup parts. Then I removed the old cam return spring, the old cam (and the old spring underneath the cam) and the old bi-metal switch. The instructions were pretty clear on how to install the new style return spring and new cam. Then I installed the new bi-metal switch.

Really, the hardest part of the whole repair is getting the door panels back in the proper place so that the screw holes are aligned. That probably took longer than the rest of the repair job.

The new parts have the detergent cup working like new again. Very satisfying repair!

I removed the old flange pieces before ordering the new one, then repositioned the washer after attaching the new one to the washer top. I then attached the flange to the counter top resulting in a more stable appliance. It was simple to remove the screws and install the new flange.

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

Just as everybody explained, 4 screws for the door panel, 6 screws for the dispenser, out and in, 15 minutes!!! There are plenty of screws on the door but, once i knew i was looking for 4 screws, it was a cinch!!! Thanks for that tip. All my appliances are the same age so i 'll be back to this site again!!

first I removed the 4 screws that hold the bottom part of the door cover and then removed the 6 bolts
with a power screw driver with nut attachment.I then reomved the 2 wires which are color coded and noted which one went where.I removed the old unit and installed the gasget and new detergengent cup,the wires,bolts and door screws.You do not have to remove the screws to the top part of the door.The screws are located inside the door on each side. Took about 20 minutes.

Since the bimetal repair kit was not available, I bought the complete detergent cup, gasket, and bimetal switch assembly set. This was still far cheaper than paying for a professional repair. All I had to do after shutting off the power is to remove screws to open up the door (door trim/6 screws & 6 screws on the inner side of door edges to remove outer wall of door). The detergent cup assembly is right there for easy access! I unplugged the 2 electric wire plugs to the bimetal switch (paying attention to which plug goes where for when I reassemble), removed the 6 screws that mount the cup assembly, removed assembly and gasket, cleaned the surfaces, and reassembled with the new assembly. Very, very easy to do and everything works like a charm!

New pump housing filter was needed as the old one was plugged and distorted.

I

this is a portable unit
the wood top is removed this allows access to the side cabinet screws and the lower front trim screws behind the lower front trim panel you can access the hose connections disconnect and reinstall
new part works great!

First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.

1. Removed the four screws to remove the door front.
2. Removed the six screws to remove the detergent cup.
3. Replaced bimetal strip, cam, and spring. (simple task)
4. Replaced gasket and seal.
5. Replaced detergent cup.
6. Replaced door front.

Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

Typically when the detergent is not being despensed during the wash cycle, the bi-metal switch is bad (they don't tend to last forever). I took the 4 lower screws out from the inside of the dishwasher door,, unscrewed the bi-metal switch, and screwed in the new switch. I also decided to replace the metal spring for the dish as well, which took the majority of the time. Once you get the idea of how that spring is wound in there, the install goes pretty quickly.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

found the parts ordered them an poof dishwasher us as good as new