MDB6658AWQ Maytag Dishwasher - Instructions

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

We had tried to use dish washer cleaners, and they would work for a time, but we started spending more money on cleaner than we wanted. I ordered and then I replaced the lower spray arm. It took a little effort to get the top screw off, due to hard water deposits. The new one went on very easily, just screwed right in like the old one. It's working great and I really don't mind not getting a new one or paying for a service call!!!

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!

I reversed the tub wheel, cut off the protruding flanges so that the end of the axel pin was exposed. Then using a small socket I placed a split washer over the end of the pin, used the socket to hold the washer in place and tapped it into place with a hammer. Note there is a grove around the circumference of the pin which holds the split washer. This locked the tub wheel onto the pin and it still rolled freely. Unconventional but it worked great.

Removed top retaining piece by turning clockwise to remove spinning spray arm from bottom assembly. Removed the 6 retaining screws from the primary screen pump cover and lifted up. Removed filter and the four pronged piece that spins with the filter. Removed the 3 hex head screws that held the secondary filter assembly & pump cover in place. Removed center screw that held the bottom black plastic piece just above the secondary filter bottom. Inspected the cutter, then started reassembly in reverse for the replacement of new parts and filters.

I didn't know how to put in the new one clips until I looked up a picture of them in place, on-line. Once I saw the picture, it was a matter of clipping the new ones in place.

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

My hand was broken for some time. I decided to replaced the latch assembly also. Started to find a part and fix it. PartSelect was an excellent choice. Parts were easy to find with the model number. The fix was very easy. 1. powered off dishwasher at breaker panel. 2. removed the screws attaching the inside of the door panel. 3. raised up panel while disconnecting the four door latch cables.. 4. Handle was broken so it just fell off the latch. CAUTION - handle can be put on backwards - "my experience". re-Installed the handle correctly, 5. installed the four cables back on the latch. 6. placed the inside door panel back in its correct position. 7. installed the screws. 8. turned power back on. Job Complete

Ordered BOTH the front and rear tines as the front tine showed some superficial rust through the plastic covering in a couple of spots. Re-used the tine holders which were still solid condition and flexible. Snapped bowl holder tine unit out of dishwasher, snapped new tines in place, snapped unit back in dishwasher. Took 5 minutes or less. All other parts of the dishwasher rack were still in excellent condition with no cracked spots on the vinyl covering or rusted spots visible anwhere.

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

I discovered that, except for the central tower, all the spray holes were all plugged with I took to be calcium deposites . Using the parts diagram located on this web site, I removed parts. All parts can be removed either by hand, nutdriver or small wrench however you do need a star drive (simliar to an allen wrench) to remove the Pump Cover and Secondary Filter. The Lower Spray Arm unsnaps from the Pump Cover and Secondary Filter. I laboriously removed the deposits from each part down as far as the support filter. The upper spray arm can be removed by unsnapping the hub. the Pump Cover and Secondary Filter is a closed unit so. I purchased a new one. The process is very labor intensive. Next time I am going to consider purchasing all new parts or calling a repair man.

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

Had a repairman come to clean out all the food that had gathered at the base. Once he showed me how to take the spinner off I was able to order the parts and install them in no time. It works great now. Repairman and parts cost me $100, better than buying a new one.