MDB6650AWW Maytag Dishwasher - Instructions

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Sooooooooo, I ordered a new kick plate, it arrived promptly, tried installing it and it was being difficult. Removed plate above that and lined up new plate(kick plate) tried putting plate above it on and as when we installed the machine that upper plate was difficult. Removed upper plate to fcheck problem of installation and guess what? Stuck in the inside of the upper plate was the lower plate complete with sound insulation. Happy ending :-)

Removed the inside door panel. Had to borrow a friends power screwdriver with a star shaped bit to do this. Removed old latch and inserted new one catching the prongs so they could now lock and unlock by pulling up on the latch. rescrewed the inside door back and all was done.

First, I turned off the power to the dishwasher at the main box. Then I removed the 10 screws holding the interior stainless steal cover to the door. I removed the broken handle and the broken piece from the door. I snapped the new handle in place and replaced the 10 screws before turning on the power.

This was the easiest repair job I've done and it saved me at least $100 dollars in labor.

Thanks to all who have submited their stories. Great help!

Removed inner stainless steel shell of the door,revealing the broken latch/door handle. The old one fell out, and the new one snapped in. It was as easy as that!

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

removed old damaged tines and snapped new tines into place. Saved myself some cash, received the product in less then 5 days and did not have to drive over to the appliance store in the next town and wait two weeks for them to place the order and at a substantial savings. I'll use your service again when needed.

Donald R. Daily Sr.

Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

First I turned off the circuit breaker to dishwasher. Then removed the lower spinner and related parts. The water in the bottom needs to be sucked out with a shop vac next, because when the pump screws are removed any remaining water will drain underneath onto the floor. Remove the wash pump and drain rotor.
Remove the front bottom plate to access underneath, unplug the electric motor and thermister. Unscrew both hoses,drain and upper wash arm. Move the locking ring to release the the entire assembly up into the dishwasher.
The kit I bought had most of all the washer parts included, so on reassembly I used the new ones. The rest when back together in reverse order after a good cleaning. Since the thing was apart anyway why not clean up all the filters on reassembly. The kit also came with complete instructions.

I took apart the lower spray arm apart and removed the 6 hex screws. I noticed that the little plastic circle thing had been ripped off the dome-shaped thing. I replaced the part and put it all back together.

Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!

Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.