MDB9150AWB Maytag Dishwasher - Instructions

I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.

I ordered the parts after looking at the diagrams. I ordered a total of 5 pieces.
The parts arrive earlier than expected, and were new, OEM, parts. I cannot stress how important it is to order Original Equipment Manufacturer parts.
I replaced the broken pieces within 30 minutes. Great experience.

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

removed old and broken and replaced. The best part was, the turn around time from partselect. The fastest delivery of anything I ordered that part a 2 in the afternoon and had it the NEXT day, without specifiying any extra rush shipping. Right part too! Amazing job! Thanks

Unscrewed the 2 screws securing the dishwasher to the counter. Unscrewed 2 front panels. Shut off water valve. Disconnected water intake. Pulled dishwasher out 5 inches. Removed broken spring, replaced it. Checked the door movement. Scrubbed the door rubber gasket of calcium deposits & debris. Replaced the Teflon tape on the water intake. Reconnected water hose. Opened water valve. Checked for leaks at the water intake location. Ran 1 dishwasher cycle again for leaks. Pushed the dishwasher back under the counter. Secured the 2 screws on top of the dishwasher to the counter. Reattached the 2 front panels and enjoyed a glass of wine.

Turn off power, remove the lower kick plate and lower trim panel with the nutdriver. The float switch is in the front on the left. Remove the two wires on the switch. Use a #1 philips to remove the one screw holding the switch to the frame. Remove switch. Install wires on new switch and install switch using the screw. Be sure to get the plastic float arm under the switch. Raise float and observe the switch clicking on and off. Replace lower plates and restore power.

***BEFORE STARTING BE SURE TO TURN OFF THE POWER!!
THE SPRING TENSION WAS GONE THAT WOULD KEEP THE DOOR FROM FALLING. KEEP IN MIND THERE IS A DOOR SPRING AND LINKAGE ON BOTH SIDES OF THE DOOR. SO BUY 2 OF EACH AND RETURN THE ONES YOU DON'T USE. IF YOU REPLACE THE LINKAGE ON ONE SIDE YOU MIGHT AS WELL CHANGE THE OTHER ONE SINCE IT'S ONLY A SMALL PLASTIC PIECE.
FOR ME THE SPRING WAS GOOD - ONLY REPLACED THE LINKAGE. REMOVED THE PANEL AT THE BOTTOM AND THE 2 SCREWS THAT HELD IT UNDER THE COUNTER TOP. I DIDN'T DISCONNECT THE WATER BUT WAS ABLE TO PULL THE UNIT OUT JUST ENOUGH (10 INCHES OR SO) TO GET TO THE SPRING. HELD IT IN PLACE WITH THE VISE GRIP SO IT DIDN'T FALL BEHIND THE UNIT. FYI - YOU MIGHT HAVE TO ADJUST THE TENSIONER ON THE BOTTOM IF YOUR SPRING TOOK A WALK WHEN THE LINKAGE BROKE. BE CAREFUL PUSHING THE UNIT BACK UNDER THE COUNTER. TOOK ME ABOUT AN HOUR AND SAVED SOME MONEY

On my dishwasher, one linkage broke, making the door feel heavy to raise and lower. Because there are two door springs, one on either side, I decided to replace both plastic linkages even though only one broke, because it would only be a matter of time before the other plastic link failed and I would have to do the repair all over again. Remove the 2-piece panel at the bottom front of the dishwasher. It's held on by four hex-head screws which also have slots for a Philips screwdriver. The springs can now be seen on both sides of the door, at the bottom. Remove two screws that anchor the dishwasher to the underside of the counter. Gently ease the dishwasher a short distance out from its under-counter recess, just far enough to gain access to the springs. Make sure not to put any excessive strain on the water inlet tubing, drain hose or electric power cable by pulling the dishwasher out too far. Close and latch the dishwasher door so that the springs are in minimum tension. Note the slot that the linkages hook into on the door levers. Hook the small end of the spring into the hole in the metal bracket. Slide the linkage onto the other end of the spring. Stretch the spring to slide the free end of the linkage onto the door lever and into the appropriate slot. Push the dishwasher back into its recess and replace all screws and panels.

I took off bottom front and kick plate. Retrieved the spring which had flown to the rear of the unit. Cannot pull unit out because the trim piece on the counter top was put in after the unit was screwed to the underside of the counter. So... I noticed that you could move the plate the bottom of the spring hooked into by unscrewing a long quarter inch hex head bolt and bring the plate forward where I could hook the bottom of the spring into the plate. I had first hung the door spring linkage on the door (looked at the opposite side to see how it was arranged) then onto the top of the spring. The difficult part was keeping the bottom of the spring in its hole in the plate while moving the plate back in place. After I got it past the flange where the bolt screwed in, I screwed the bolt in and pulled the plate back to match the opposite side distance which put tension on the spring. The door now works. I am fortunate to have my husband's tools available.