MDB9750BWW10 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Doug from SANDIA PARK, NM
- Parts Used:
- WPW10192799
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Grit on all the dishes, spots on glasses and hard water buildup inside the entire dishwasher
1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order
Was this instruction helpful to you?
Thank you for voting!
Upper rack wheel broken
Four screws were removed and new parts were installed. The only problem was that two types of rack adjusters exist. If your dishwasher does not have a lever, part number PS2100470, then the new rack adjuster either left or right side will not work without part numbers PS2100470(lever) and PS2100308(cover). Be sure to order parts for both sides since the original plastic wheel supports have been replaced with steel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from St Augustine, FL
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heating Element Corroded
Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lizbeth from Kingston, TN
- Parts Used:
- 6-918651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bottom of the flatware basket broke out
Replaced with new basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Philadelphia, PA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Latch Asembly Broke, Door wouldn't close properly
The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from McHenry, IL
- Parts Used:
- WP99002614
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Jet Dry would leak out of the reservoir tank.
Not much to report on this repair. I removed and discarded the old rinse aid knob, and replaced it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Pickerington, OH
- Parts Used:
- WP6-917647
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cups and glasses on upper rack were not getting clean.
Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.
The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.
The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Billings, MT
- Parts Used:
- WP6-917647
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishes were not getting clean on the top rack.
The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from Duvall, WA
- Parts Used:
- 99002624
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
old wash arm was cracked and had gunk in it.
The upper arm assembly removes easily by unsnapping a plastic part or two that holds it in place.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Miami beach, FL
- Parts Used:
- WP99003281
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Railstop disappeared
Slipped it on the upper rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Chester, NH
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut
Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francine from Bristol, CT
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top wash arm kept falling off.
I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Franklin, WI
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher arm keeps falling off.
I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veryle Lynn from Lake Lure, NC
- Parts Used:
- 6-918651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
basket was broken
took out the old basket and put in the new one which required no tools
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Croton on Hudson, NY
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch handle broke, making it hard to open the door.
Removed ~12 screws holding the inside liner onto the door. Pulled off the two connectors (one with black and one with white wires). Replace the handle and latch mechanism. Redid connections and replaced screws. Viola. (Be sure to buy BOTH the handle and latch mechanism- I don't see how you could easily install the handle on the mechanism myself, and what broken in my case was the black handle).
Was this instruction helpful to you?
Thank you for voting!