MDB9750BWW10 Maytag Dishwasher - Instructions

FIrst I went to your web site; located the part on the easy to read diagram. Next I ordered the part. When the part came to the house (2-3 days), I opened the box and then the packaging, I screwed the part in and Wala! Boom! Bang! She was fixed!

All kidding aside. The part order was quick to locate, quick to ship and one of the easiest companies to deal with. I will return on my next dyi project.

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

one: removed old baskets
two: and put in new baskets.

Opened door

Put in place

Closed door

Whined about being tired

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

Shut off the electricity to the dishwasher. I removed all 11 screws from the door panel. After separating the 2 door panels, I removed the 2 door switches from the door handle ( I used a flat head screw driver to help get them out). Then I unplugged the 2 switches and plugged in the new ones. I replaced the door switches into the door handle ( this was not an exact fit because the new switches is slightly larger than the old ones). I put the new switches in place as tight as I could in the handle. I screwed the 2 screws holding the handle first to secure it before I put all the other screws in the door panel. I turned the electricity to the dishwasher back on. Our dishwasher has been working perfect ever since then and it is over 10 years old.

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

Our dishwasher broke just before the big Christmas dinner! We ordered the matching part from your website and rush delivered it. We then removed the old part with a screw driver and replaced it with the new part. It fit perfectly and the dishwasher was back in operation. Christmas was saved!
Thank you!

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

I had to remove rack, remove old assembly and replace with new part. The manufacturer has improved the replacement part, which leads me to believe I am not alone. I used a nut driver/ allen wrech to remove broken part and took about 10-15 mins to repair. Part arrived very fast, great service!

remomed old adjuster and attached the new one to the housing and it was done it was very simple

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer