KUDM24SEAL2 KitchenAid Dishwasher - Instructions

Took off the front cover and scraped out soap deposits - probably consequent to wash water not being hot enough. Replaced the lower seal - used some automotive weatherstrip seal to cement it in place. Loosened the door per instruction sheet and replaced the water deflectors on each lower corner. Probably took me longer since I'm 81 years old and don't get up and down as well as I once did. Insulated the hot water tube so wash water is hotter than before. Works pretty good.

The lower door seal had fallen out as it was worn out so I wasn't sure of the proper orientation of the new seal or even where it went as the instructions had nothing about the seal. A little bit of logical thinking and the seal just just snapped in place. The door drains that came with the kit were both a right or left hand and so I didn't install them. Turns out that I didn't need the new ones anyway. The old door seal just pulled out and the new one just pushed into place. I was careful to center the top of the strip so that it would come out even at both sides of the bottom. There were no instructions for the door seal but none were needed. As long as I was working on the washer I did some cleaning to make it look new and bright...that took the most time. Easy repair and a happy wife besides.

Contrary to info on your website, the bezel is removed by turning it counterclockwise. This misinformation wasted a lot of time. The bezel is difficult to turn. I used a home-built wrench: drive two screws spaced 3 inches apart through a stick of wood, projecting 5/8 inch. Engage the screws in the slot in the bezel and in the grill, and turn ccw. I cleaned the deposits from the surface where the gasket seals with white vinegar. New gasket and bezel fixed the problem.

replaced the fuse in the door

Took 6 screws off to disassemble the control panel, removed the electonics, removed and ordered handle, and replaced it.

Smooth.

all I had to do was snap the plastic piece in.
thanks, great experience.

We were told by a repair guy to buy a new dishwasher-about a $900+ cost to replace. Then a local parts place and Sears each quoted us $85 for the part plus $129 to come out. Found your website and bought the part for $17. Also bought a hard rubber gasket that fits on the bottom of the door for $8. The brackets that came with that last part were the hardest to install, but the gaskets took 15 minutes. We did glue another strip of the long door gasket along the area under the door lip. Works great! Saved over $800. You rock!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I read the instuctions and snapped it together just following the pictures...reading only when the picture was not enough information for me. My husband thought I pulled it out of the box already put togethr, he did not know I put it together.

Grabbed old seal and removed it.(notice how seal was situated in slot)

Pushed new seal in slot that held old seal. close door.

If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

The repair was very simple once I figured out that all I had to do was peel off the damaged insert, clean the plastic surface with WD-40, and stick on the new insert.
But, I made the job much more difficult because I thought the insert was installed from inside the door. So, I removed the inner door panel as well as the control board equipped with sealed switches. My error -- but would have been helpful to have simple instructions on how to peel off the damaged insert and install new one.

Replaced the lower washer arm retaining nut,bearing ring.and seal in about 3 min.The retaining nut had broken off inside - make sure to remove the broken piece-I used needle nose pliers.
The dispenser took about 35 mins. Removed all the screws around the inside of the door and removed panel.Removed screws holding the dispenser and replaced.I took time to give the dishwasher a good cleaning(inside edge).
Now my wife is happy.

Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

remove the lower arm and pieces.. get the parts stacked in the right order and hand screw the retainer nut... done! I decided to spend a little more and replace the whole washer arm and I'm glad I did. My dishes are coming out clear then they have in years!! Ordered the parts Thurs morning... thought i might get a load or two done but when I opened the washer on friday it was obvious I was facing a weekend of teens having to handwash dishes! 15 minutes later the doorbell rang and there were the parts!! Woo Hoo!!