Models > KUDS21SS2 > Instructions

KUDS21SS2 KitchenAid Dishwasher - Instructions

Jump to:

All Instructions for the KUDS21SS2
46 - 60 of 81
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from East Brunswick, NJ
Parts Used:
WP4162322, 4162321
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Replace 2 Wheels
One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christopher from Lexington, MA
Parts Used:
WP4162322, 4162321
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Axles on lower rack broken
Very, very simple. The axles are nylon plastic and snap into the plastic-coated metal grid that forms the lower dishwasher rack. Over time they get brittle and break.
Replacement consists of snapping the old axle out of the rack and snapping the new one in. I replaced some of the wheels at the same time, as we had lost them. The wheels don't seem to wear out, so if you did this repair in time, you could re-use the wheels.
These little axles are EXPENSIVE ($3.50 each!), but for $30 you can replace all eight of them, and your dishwasher rack will work like new again!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Curt from San Anselmo, CA
Parts Used:
WP4162322, 4162321
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
roller wheels & axles broken
Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Helen from Vienna, VA
Parts Used:
WP4162322, 4162321
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
wheels and axles had broken off rack - not able to slide in/out smoothly anymore
Simply popped on new axles and wheels and dishwasher works like new!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Sharon, PA
Parts Used:
4171221
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
cap broke
screwed it in. Closed the door. Voila, it works!
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Twin MT, NH
Parts Used:
WP4162322, 4162321
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Wheels And Holders
Warm rollers and holders in warm water for 2 min each slide on all done
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from coumbus, OH
Parts Used:
WP4162322, 4162321
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
broken roller weels on bottom dish rack
I simply removed the broken wheel brackets and snapped new ones on. then the wheel just sliped on. It took some good hand strength.
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
douglas from stocholm, NJ
Parts Used:
WP9743413
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set, Wrench set
water not going into dishwasher
While replacing the water valve I broke the float switch. Ordered the switch....it was here in 2 days. Great service! Will use this company again....I hope not all that much. lol
I am a retired Sears service tech, but not a dishwaher tech.
Love Parts Select!
Thanks guys,
Doug
1 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Boynton Beach, FL
Parts Used:
350930
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
23 of 76 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Norman, OK
Parts Used:
WP4162568
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Detergent dispenser failed to open
Removed the door cover and replaced the bi-metal.
5 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Duxbury, MA
Parts Used:
W10207863, WP8531743, WP9743413, 9743070
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)
Old float stem had fine thread new one had corse and did not supply nut so had to use old one over.
put new switch and new gasket on old float stem with old nut. but it still overflows about 1/2 cup of water through stem
10 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Albert from Highland, TX
Parts Used:
4169400
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Replaced black panels with stainless.
Just followed directions included.Am extremely pleased with the appearance of the new panels they matched my new appliances.Also I did not pay for express freight but received my order in only two days.Very pleased with Part Select.Thanks Al S
Was this instruction helpful to you?
Thank you for voting!
Customer:
Megan from Pacific Palisades, CA
Parts Used:
WP4162322, 4162321
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Roller Wheel on lower dish rack broke- rack didn't sit or roll properly.
used screwdriver to remove roller axle. Snapped on new axle and wheel. I ordered two extra sets just in case future wheels brake. simple. 16 Year old dishwasher works fine!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Carlisle, PA
Parts Used:
WP4162568
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Soap Cup Lid was not opening during main wash cycle
Very easy. Disconnect power to the dishwasher via a breaker or fuse. Open the door and remove just the 4 screws on the inside lip of the door. Do not remove the screws hoding the closing brackets. Remove the front glass and chrome panel between the control panel and the kick panel. This will give you access to the soap cup and bi-metal. Remove the one retaining screw and remove the bi-metal,taking note of the position of the wires. Remove the wires, by grasping the connectors (I used needle nose pliers for this), not the wires, and re-intsall them on the new bi-metal. Re-install bi-metal on soap cup assembly, "cock" the release lever by closing the soap cup cover and manually trip the bi-metal to make sure it will release the lever and open the cover. Re-install the front panel with screws. Restore power and test appliance.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sean from San Francisco, CA
Parts Used:
WP4162322, 4162321
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
A few rollers and axels had gone missing
Easily one of the easiest repairs I have ever done. The new bits snapped into place and now the bottom rack rolls in and out like brand new.The ease and speed of finding the parts was really helpful. This is an old model and to be able to find the exact parts I needed so fast and so cheap was great. Oh and they arrived the day after I ordered them! Insanely fast!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KUDS21SS2
46 - 60 of 81