KUDS21SS2 KitchenAid Dishwasher - Instructions

removed screws from dishwasher and discovered i could replace panel because of door type

Simply replaced the wheels/axiles and brackets using functioning ones as template. No problem at all.

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!

Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!

Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Warm rollers and holders in warm water for 2 min each slide on all done

Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.

I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to catch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.

After checking for blockages in the drain line and finding none, I disassembled the wash wand assembly and discovered a gasket that had really deteriorated. Since there was nothing else apparently wrong, I took a chance and went shopping for the gasket. None of my local stores could provided me one so I searched on line and found it at Partselect. It had to be special ordered and that took a while, but when it arrived, I put the new gasket in and had a perfect dishwasher again for less than 15 bucks. The schematic I was able to print from your website was invaluable.

The hardest thing was getting the old one off and easy snapped the new one on

Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.