KUDL01ILBS0 KitchenAid Dishwasher - Instructions

The part snaps on using two plastic retainers (included). You have to pull down gently on the feed tube at the top of the dishwasher to set the top retainer. After that it's a piece of cake.

Partial disassembly determined thar the plastic handle was broken and a tensnioning spring was missing (had fallen out of reach within door) Ordered new replacement parts and received next day. Great delivery service. Installed in short time by removing four screws, disconnecting two wires and reversing procedures to reassemble. Finding parts on line was a great help and the delivery service was great,

First research then troubleshoot
Removed
1 Upper rack
2 Lower rack
3 Lower Wash Arm and Strainer Parts
4 Upper Wash and Rinse Parts
5 Accumulator assy.
6 Motor shield
7 Inlet protector (most difficult)
Noticed blade was broken off chopper assy.
Replaced chopper assy.
Runs and cleans like new.
Most difficult step was to remove Inlet protector
After removing two torx screws (#15) used small pry bar to lift inlet protector from position. Not easy to accomplish with hands alone. Inlet protector fits tightly into position.

Checked the house circuit breaker, verified AC to the box under the dishwasher, removed the screws around the inside door cover, and removed the cover. Removed the outer circuit board cover. Used a multi-meter to verify AC to the door latch, and to verify the latch switch was working. Verified AC to the thermal fuse above the circuit board when the door latch was closed. Verified no AC on the other side of the thermal fuse. Removed the thermal fuse connections with pliers. Used thin flat blade screw driver to unsnap the thermal fuse assembly. Used multi-meter to verify no continuity through the fuse. Ordered the fuse assembly and replaced. Reconnected the thermal fuse connections. Manually closed door switch and saw lights on the display panel, and dishwasher started. Replaced all covers and works great.

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Found the gasket to be wearing out. Once I got the part I took everything apart inside to find that I could have just taken the dishwasher out and replaced from the bottom. It was not difficult, but I've installed a ton of dishwashers. For the average homeowner, this is can be a difficult job since it requires plumbing and electrical skills.

Need torx to remove front panel. There are four screws that hold the control panel that don't need to be removed. If you do remove them, it helps to put the control panel back before you reinstall the front. The six screws that hold the soap dispenser are a very small hex (<1/4, maybe 3/16). It would help to have some small sockets or nut drivers handy for this.

The door balance is easy.

Replaced the switch, that did not fix it, but a new circuit card did

Removed back of door to access the screws holding on the air inlet. The top of the door with the controls does not need to be removed, I found out--only the bottom part. Accessing the 5 screws was difficult as there was no space to get the socket onto the screws at a 90 degree angle. Also, there are two plastic shields that fall off when you remove the inlet that need to be replaced, with difficulty because of the accessibility to the area.

PartSelect site is excellent and finding the correct part was relatively simple, although I was not absolutely sure I ordered the right part until it arrived--only one day after ordering, although I paid for the least S&H option.

After replacing broken door cables I had a small leak at the door corner. I replaced door seal with that not fixing the leak and found that the door hinges were bent a little from the cables being broke for awile. Installed new hinges and leak is fixed now. A little difficult but once unit was pulled out about 6 inches the hinges were not bad to replace

1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.