KUDE60HXSS1 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from SAINT CHARLES, MO
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Was this instruction helpful to you?
Thank you for voting!
Slide Track both sides
Was easy to do but would recommend getting the 4 bolts that hold both racks in. The ones on the left side had rusted and hard to remove and reuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from HIGGINSVILLE, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Mounting bracket
Removed old part and replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUBURNDALE, WI
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ELGIN, IL
- Parts Used:
- W10864081
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking door seal
Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Briant from Byron, MN
- Parts Used:
- 4317824
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Miami, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Factory crimped end of link cord pulled out of plastic fastner that hooks on door.
Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Fredericksburg, VA
- Parts Used:
- WPW10077881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part melted in the d/w
screwed the new cap on, voila. just need to make sure you look and get the right cap; lots of different ones available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from racine, WI
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced lower rack wheel assembly
watched video took less than 5 min to replace veeeery easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from NAUGATUCK, CT
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water leak during wash cycle
I followed the video on the site and it worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from CHAPEL HILL, TN
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leaking around door
Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from KINGWOOD, TX
- Parts Used:
- W11177741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Slow water drip on bottom side of door, both sides.
Pulled off old seal. Pressed into groove the new door seal. No parts required.
Was this instruction helpful to you?
Thank you for voting!
Hinge bent went spring cable broke
My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...
Was this instruction helpful to you?
Thank you for voting!