KUDE50CXSS0 KitchenAid Dishwasher - Instructions

The repair was similar to the very good video provided by PartSelect. However, I did make a few changes. The new rack was slightly different in the front side compared to the old rusted rack. After I removed the old rack from the dishwasher, I placed the two racks side-by -side to make sure they were compatible. They were identical in the rear structure and overall size, so I proceeded to change out the wheel racks, rack height adjusters and upper wash arm to the new rack. I suggest transferring each part one at a time so you can get the spacing correct. Also, in my case, many of the items needed to be washed with water to remove soap buildup in these parts before moving to the new rack. I would also suggest putting the upper wash arm (needed in this case) on the new rack last. The total job took me about an hour including washing or rinsing all parts and reassembly. This is an easy job, just take your time and do one item at a time so nothing gets mixed up. I used a drill driver to remove a total of 4 Phillip head screws for the rack height adjusters but a regular Phillip head screw driver would work as well.

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Removed old housing parts and replaced them with the new parts I ordered. Very easy

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most

First electrical power to the dish washer was turned off. The top portion of front door panel was then opened up to expose pocket handle and latch assembly. Old latch assembly was replaced with new latch assembly and a new fuse. The door panel was then re-closed and electrical power turned on.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Although the b&w photos spooked me a bit. I quickly learned to tear off/break off the old adjuster arms, and then refer to the written directions for installing the new parts. Don't waste your time trying to figure out removal of the original parts, just get them off. So, I did not find the photos helpful, but I figured it out.,with help from the text And of course, once you do one side, the other side is a breeze!

unplug, disconnect water, remove all screws holding the machine in the cabinet. slide out the machine to access the 4 bolts hold the rail. Have a prop to hold basket in place as you remove old rail> Plastic clips front and back, hold the basket to the rail. Be careful not to break, not include with the replacement rail. If you are not handy with tools and no insight...hire it done

like the instructions showed

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.