KUDS01ILBL6 KitchenAid Dishwasher - Instructions

Replaced electronic control panel first which had an obvious defect (burned terminal). Still no power. Replaced fuse and works fine now. Took lots of reading to find out the dishwasher had a replacable fuse. Even the appliance store didn't know.

Via your web-site I was able to download the step-by-step screen-shot pictures. I was really surprised on how easy the detailed photo screen shots made the repair really easy! Thanks for making this repair a piece of cake. If I should ever need additional parts for any of my home appliances I will certainly order my parts through PartSelect.

Got Maintenance Flyer out an read about problem
Removed access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ

The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem

The cycle select buttons on the top of the door worked and would light, however, the power button did not function and did not light. The faulty part ended up not being the control board but the control panel, which included the power button. I spent a good amount of time troubleshooting the problem until I figured this out. The part number was (8531257) Panel-cntl.

Thanks to the previous review of this part, I was able to figure out how to do the replacement myself and saving $150 on a service call. The part is super easy to replace. Remove the screws on the door, lift the outside piece of the door up and off the hinges and then unplug the old piece. I had turned off the electricity to the dishwasher to avoid getting shocked. There were 4 hex nut screws holding the part in, removed those & popped out the old part. Installed the new one, put the door back on and the screws, turned it on and no leaks. This part was so easy to replace, even for a 52 year old woman like myself!

I had to getto the side of the machine. After that, it was simply removing 4 screws and removing the old part, replacing the screws and putting the rack back in the track.

I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

I had no lights on the console. Found the internal fuse blown, as I was looking around noticed the door latch also broken so I replaced that as well. Items were easy to identify from the bom and repairs completed in about 15-20 minutes. Dishes all clean now.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.

1, I shut off ac circuit breaker.
2.Shut off water supply valve.
3.disconnected water line from inlet valve.
4. disconnect the drainage hose.
5. have plenty of towels to mop up water.
6. Remove racks and disconnect water diverters inside the tub.
7. remove phillips head screws that hold dish washer to counter.
8, Pull out DW and lay on its side to expose bottom of dishwasher. disconnect the motor terminal plug. and disconnect the temp prope.
9. disconnect the drainage tube and then proceed to remove the 3 plastic clips that hold the pump housing to the tub.
10. I used some silcone grease around the new pump housing to be safe. then I installed the new pump housing and motor in the reverse order.

It probally took me about an hour start to finish, the hardest part was placing new housing back in. The ring around the bottom of tub is very sharp!
Left some blood there.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

My husband pulled out the dishwasher and removed the faulty part and installed the new one. We found info on the parts source website to assist us. Dishwasher works great!!! Someone from the company we purchased it from had replaced it several years ago, and the seal at the bottom had leaked and the motor had siezed because of the water. We also discoved that the water line was severly kinked in 2 places, so we installed a flexable hose. Now my dishwasher is quiet, fills much faster and all this for a fraction of the price of a new appliance. Would recommend this website.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.