KUDM24SEBL4 KitchenAid Dishwasher - Instructions

Took the bottom panel off and felt with fingers to replace spring with out pulling dishwasher out from enclosure.
Fairly simple

Mine is a Ultra Wash 111
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg

Removed the inner door panel and then the circuit board protective cover (which just snaps in). Fuse assembly is readily accessible and just snaps in. The wires are attached with spade lugs using existing wiring. No wiring modificatins needed,

1) Removed the two panels below the door.
2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing.
3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side.
4) Removed the broken spring.
5) Attached the new spring.
6) Openned and closed the door to make sure spring was tight enough.
7) Pushed dishwasher back in.
8) Rescrewed cabinet facing screws
9) Rescrewed floor panels.

Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.

Install too less that a minute. Fit perfectly.

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.

I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.

Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.

The repair was simple except for removing the thread portion of the old retainer nut from the lower housing. I had to remove the lower housing and separate the male threads of the old plastic nut from the female threads in the lower housing. That took 25 minutes since I did not want to ruin the female threads. Once removed, the new parts went into place easily.

I removed the door gasket first by sliding it out.Then I pulled the door seal out. It suggested removing the springs,very hard to find and do, so we left them in place and did not use two parts of the kit because they were still good.
Putting in the door seal was a bit tricky because we had to use something to push it into the groove.That was the reason for the credit card. It was easier to push it into groove rather than doing it with a screw drive for fear of punacturing a hole in the rubber gasket. It worked well. Then we kept checking to see if the door shut properly, It was tight at first, but seemed a little better after adjusting the seal a bit.No leaks after that.