KUDI25CHAL0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Flemington, NJ
- Parts Used:
- 675796
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher simply stopped during operation for no apparent reason.
Removed the inner door panel and then the circuit board protective cover (which just snaps in). Fuse assembly is readily accessible and just snaps in. The wires are attached with spade lugs using existing wiring. No wiring modificatins needed,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Tinley Park, IL
- Parts Used:
- WP3379369
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper Wash Assembly Broke Apart
First I read the other repair stories and knew it was a relatively easy repair. I removed the end caps on the front of the top dish rack and removed it for ease of access to the part. I then removed the two screws holding in the old part observing how it was positioned to make sure the new part was replaced in the same manner. I put the new part in place and screwed in place and replaced the dish rack. Everything is working just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Chicago, IL
- Parts Used:
- WP8539324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
mount for top rack spinner broke
Install too less that a minute. Fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Magnolia, TX
- Parts Used:
- WP3374077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked drain hose
removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Hollister, CA
- Parts Used:
- WPW10616003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
soap dispenser spring wasn't working.
My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from Jackson, MI
- Parts Used:
- W10134647
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
replace lower rack
compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Gladewater, TX
- Parts Used:
- WPW10253040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Prongs on Upper and Lower Dish racks were rusted and broken.
I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.
As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.
I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.
The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.
As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.
I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.
The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from North Massapequa, NY
- Parts Used:
- W11164091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The wheels that make the lower rack roll had worn out to the point that sometimes dishes would rub against the spray arm.
I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Sterrett, AL
- Parts Used:
- 9743958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Tube Dry Rotted
1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from CHARLOTTESVLE, VA
- Parts Used:
- 675238
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
standing water in tub , not draining
removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanna from Smithtown, NY
- Parts Used:
- 675808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Original supply tube for upper spray assembly disintigrated
Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Fowlerville, MI
- Parts Used:
- 4172127
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Suds and water leaking from bottom of door
Bent back metal ears over door hinge pins, released door springs from door hinges. Lifted door off of hinges and replaced corner drain back seals and lower door seal.Still leaks so obviously I have another issue or the door seal is lousy quality. I've completed this project before and never had another issue for 6 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DANVILLE, PA
- Parts Used:
- WP8539324
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken spray arm mount
Removed holding stew from old style bracket. Put arm together with new mount and installed screw. Aligned arm with upper rack and just clicked on. Ensuring spray arm spun freely and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Sayre, PA
- Parts Used:
- WP3374077
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Original drain hose developed a leak
The repair went well with the major problem being I replaced the drain hose without removing the dishwasher from it's position. Due to this I removed the drain end with out being able to see the hose and put it back on by feel. Over all I was back up and running with in 30 minutes and everything has worked very well so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dayton, OH
- Parts Used:
- WPW10616003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Detergent and rinse aid dispenser not working
Replaced dispenser. Leaked around dispenser the first time i installed. Re-tightened mounting screws and everything worked OK.
Was this instruction helpful to you?
Thank you for voting!