KUDC25CHBT0 KitchenAid Dishwasher - Instructions

Removed old phillips head screws /w washers from spray arm kit and mounting bracket. (You'll need to keep one screw/washer set.) Attached new mounting bracket and screwed securely. Attached spray arm with new screw/washer and I was good to go. Piece of cake!

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

I looked up the part on the Internet and checked locally. The part had to be ordered locallybso I placed my order on line. The part came quickly and the instructions were fairly clear. The parts just clipped together which made it vey easy to so and it is nicer than the rack we had before.

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

At first I considered replacing the gasket on my own but was not sure If that was the problem. I had a service person come in (at great expense) to tell me it may or may not be the problem but he could order the gasket and replace it. I did it myself.

I removed the old gasket by hand, simply by pulling it out of its track. I sprayed clean water in the track to clean out old soap and debris. I soaked the new part in warm water for a few minutes to soften and lubricate it. I centered the gasket in position and began pushing it into the track with a one inch putty knife, being careful not to damage the rubber. There is a slot along the gasket that will accept a flat tool to push it in. At the corners, I had to use a screwdriver to work around the curves. In a few minutes the gasket was in and no more leaks. It couldn't be easier.

just pay attention to how the old gasket was installed, then pay close attention to how you remove it from its groove. replace with flat sides and grooves just the same.. I actually left about on third of the old gasket in place until I seated the new gasket to make sure I was doing it correctly. visually divide the gasket groove into 2 parts with the dividing line at the top of the groove, place a piece of tape on the new gasket at its middle and begin there, first one side then the other,,, that way there is no stretching to complete the circuit. easy , I am a 62 year old grandmother of 7,,,,,,,,,,,,,,,,,,,,,,,,,,,

Simply followed the instructions that were provided with the part.
Locking the inside vented piece to the outside assembly was difficult because it is located deep along the side of the dishwater (leverage) and I was not sure how much pressure to apply to the part for fear of breaking it. But it did snap into place after several attempts.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

I had replaced the control board a month or two earlier. Then smelled plastic burning. I noticed the Sta-con connecters in the molex plug had burned - that's what took out the control board. The fuse assembly came with new connectors - so you know this is a known problem with the machine. If you're handy you can buy the thermal fuse from Newark for $0.88 and replace it by soldering - but you need to replace the sta-cons. They corrode and the bad connection causes the heat making the thermal trip.

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

Took the bottom panel off and felt with fingers to replace spring with out pulling dishwasher out from enclosure.
Fairly simple